Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › from 2015.10
RM3090E _53 Suspension _008764 FRONT SUSPENSION _0049357 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 45510 1.INSTALL STEERING GEAR ASSEMBLY

Hide 48811 2.INSTALL FRONT STABILIZER BAR

a.

Install the front stabilizer bar to the front suspension crossmember so that the identification mark is positioned on the right side of the vehicle.

C149516C01
1.708,2.052 1.823,1.823 false 1.833,1.823 2.271,1.823 false 2.333,1.75 2.646,1.906 0.313,0.156 10 *a 3.313,1.375 3.625,1.531 0.313,0.156 10 *b 4.531,0.125 4.844,0.281 0.313,0.156 10 *c
*a Identification Mark *b Front of the Vehicle
*c Top of the Vehicle - -



Hide 52255B 3.INSTALL FRONT SUSPENSION MEMBER BRACE

a.
C232258C03
0.292,1.052 0.646,1.052 true 2.708,1.052 3.104,1.052 true 0.115,0.969 0.427,1.125 0.313,0.156 10 *a 3.125,0.958 3.375,1.156 0.25,0.198 10 *a
*a Protrusion


Install the front suspension member brace with the 8 bolts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)

NOTICE:

After installing the front suspension member brace, mark sure that the protrusions of the front stabilizer bar bushings are visible.



Hide 48069 4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.



Hide 48068 5.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 57104E 6.INSTALL FRONT CROSSMEMBER SUB-ASSEMBLY

a.

Using a jack, support the engine and transaxle assembly.


b.
A297334C01
0.563,0.646 0.531,0.729 false
V100135

Bolt A
V100136

Bolt B


Install the front crossmember with the 6 bolts.

Torque:
for bolt A : 96 N*m (979 kgf*cm, 71 ft.*lbf)
for bolt B : 95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 51201 7.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

NOTICE:
·

Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.

·

Use the attachments to keep the front suspension crossmember sub-assembly level.

·

The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.




b.

Tighten the bolts on the left and right sides while alternately inserting SST into the left and right side reference holes in the front suspension crossmember sub-assembly.

C234336C07
5.135,3.698 5.385,3.698 true 2.198,3.823 2.448,3.823 true 3.469,0.115 3.781,0.271 0.313,0.156 10 false *a 1.333,5.583 1.646,5.74 0.313,0.156 10 false *b 2.229,5.573 2.542,5.729 0.313,0.156 10 false *c 4.781,5.563 5.094,5.719 0.313,0.156 10 false *b 5.646,5.573 5.958,5.729 0.313,0.156 10 false *c 5.458,3.625 5.917,3.823 0.458,0.198 10 true SST 2.531,3.75 2.99,3.948 0.458,0.198 10 true SST
*a Front of the Vehicle *b OK
*c NG - -


SST
09670-00020  

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


c.

Lower the engine lifter.


d.

Install the rear engine mounting insulator with bolts A and B, and nuts C and D by tightening them in several steps.

C232246N03
3.271,1.813 3.427,2.01 0.156,0.198 10 A 4.375,1.927 4.531,2.125 0.156,0.198 10 B 3.188,2.385 3.344,2.583 0.156,0.198 10 C 4.542,2.625 4.698,2.823 0.156,0.198 10 D

Torque:
Bolt A, B, Nut C, D : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Temporarily tighten bolt A, and then fully tighten the 2 bolts and 2 nuts in the order of B, D, C, and A.



Hide 52258B 8.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH

a.
C149508N04
1.49,0.531 1.646,0.729 0.156,0.198 10 A 2.594,0.833 2.75,1.031 0.156,0.198 10 B 0.854,1.802 1.01,2 0.156,0.198 10 C

Install the front suspension member rear brace LH with the 3 bolts.

Torque:
Bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
Bolt B, C : 93 N*m (948 kgf*cm, 69 ft.*lbf)

NOTICE:

Temporarily tighten bolts A and B, and then fully tighten the 3 bolts in the order of C, B, and A.



Hide 52257A 9.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 51425B 10.INSTALL ENGINE FRONT MOUNTING BRACKET REINFORCEMENT LOWER (for 2WW and 3ZR 2WD)

a.
C338691C01
0.063,0.042 0.375,0.24 0.313,0.198 10 true *A 0.073,2.531 0.385,2.729 0.313,0.198 10 true *B
*A for 3ZR-FE (2WD)
*B for 2WW Engine


Install the engine front mounting bracket reinforcement lower with the 2 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51218A 11.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
A296303

Install the front suspension member reinforcement LH with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51217A 12.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.
A296302

Install the front suspension member reinforcement RH with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 48069 13.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Connect the front lower No. 1 suspension arm sub-assembly to the lower arm ball joint with the bolt and 2 nuts.

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)


Hide 48068 14.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45047 15.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 16.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 17.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.
C279180C01
1.719,1.781 2.031,1.938 0.313,0.156 10 *a 0.333,1.479 0.646,1.635 0.313,0.156 10 *b
*a Turn
*b Hold


Connect the front stabilizer link assembly LH to the front stabilizer bar with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.



Hide 48820B 18.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45025D 19.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 20.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 21.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 24.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 25. STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down at the corners several times to stabilizer the suspension.


Hide 48069 26.TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C279176C01
1.427,0.479 1.521,0.177 false 1.531,0.177 1.979,0.177 false 2.229,1.292 2.542,1.448 0.313,0.156 10 *a 2.115,3 2.427,3.156 0.313,0.156 10 *b 2.094,0.125 2.552,0.323 0.458,0.198 10 SST 0.979,0.25 1.135,0.448 0.156,0.198 10 A 1.042,1.917 1.198,2.115 0.156,0.198 10 B
*a Fulcrum Length
*b Turn


Using SST, tighten bolt A.

SST
09961-01270  

Torque:
without SST : 233 N*m (2376 kgf*cm, 172 ft.*lbf)
with SST : 172 N*m (1754 kgf*cm, 127 ft.*lbf)

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.

·

Use a torque wrench with a fulcrum length of 425 mm (1.39 ft.).

·

The torque value for use with SST is effective when SST is parallel to the torque wrench.

·

The final torque must be applied under standard vehicle height conditions.




b.

Tighten bolt B.

Torque:
214 N*m (2182 kgf*cm, 158 ft.*lbf)


Hide 48068 27.TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51442 28.INSTALL NO. 2 ENGINE UNDER COVER

Hide 31.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT