Home › Engine / Hybrid System › 2WW COOLING › RADIATOR › 2015.10–2016.08
RM3090E _51 Engine / Hybrid System _044377 2WW COOLING _0211187 RADIATOR A

2WW COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16058 1.INSTALL NO. 2 RADIATOR HOSE SUB-ASSEMBLY

a.

Attach the clamp to install the No. 2 radiator hose sub-assembly to the fan shroud.


Hide 16711 2.INSTALL FAN SHROUD

a.

Install the fan shroud with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17940D 3.INSTALL INTERCOOLER ASSEMBLY

Hide 16534 4.INSTALL NO. 2 RADIATOR SUPPORT

Hide 88460 5.INSTALL COOLER CONDENSER ASSEMBLY

Hide 16533 6.INSTALL UPPER RADIATOR SUPPORT

a.

Install the 2 upper radiator supports with the 4 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 16572D 7.INSTALL NO. 2 RADIATOR HOSE

a.

Install the No. 2 radiator hose to the radiator assembly and slide the clamp to secure the hose.


Hide 17362B 8.INSTALL NO. 2 AIR TUBE

a.

Install the No. 2 air tube to the intercooler assembly and No. 2 radiator support with the bolt.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.

Tighten the hose clamp to secure the No. 2 air tube.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 16400 9.INSTALL RADIATOR ASSEMBLY

a.

Install the 2 cushions.


b.

Install the radiator assembly together with the intercooler assembly to the vehicle.

NOTICE:

Do not allow the radiator assembly to interfere with other parts.



Hide 16572D 10.CONNECT NO. 2 RADIATOR HOSE

NOTICE:
·

Check that the retainer is closed when the connector is inserted.

·

If replacing the hose, apply fresh engine coolant to the O-ring.

·

Push on the connector until it makes a click sound which indicates that the connection is complete. After connecting the connector, check that the connector cannot be disconnected by pulling the connector.

·

Do not use a quick connector that has been dropped.



a.

Push in the retainer and connect the No. 2 radiator hose to the water inlet.


Hide 17343D 11.INSTALL NO. 3 AIR HOSE

a.

Connect the No. 3 air hose to the No. 2 air tube and tighten the hose clamp to secure the hose.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 17342D 12.INSTALL NO. 2 AIR HOSE

NOTICE:

If replacing the intercooler air hose, check for deposits in the intercooler assembly and intercooler air hose. If necessary, wipe up deposits.


a.

Connect the No. 2 air hose to the intercooler assembly and tighten the hose clamp to secure the hose.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 16571C 13.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the radiator assembly and slide the hose clamp to secure the hose.


Hide 16058 14.CONNECT NO. 2 RADIATOR HOSE SUB-ASSEMBLY

a.

Connect the No. 2 radiator hose sub-assembly to the radiator assembly and slide the hose clamp to secure the hose.


Hide 16282 15.CONNECT NO. 5 WATER BY-PASS HOSE

a.

Attach the clamp to connect the No. 5 water by-pass hose to the fan shroud.


b.

Connect the No. 5 water by-pass hose to the radiator assembly and slide the hose clamp to secure the hose.


Hide 53205 16.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

a.

Install the upper radiator support sub-assembly with the 4 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 18.CONNECT WIRE HARNESS

a.

Connect the 3 connectors and attach the 10 wire harness clamps to connect the wire harness to the radiator assembly and fan shroud.


Hide 16260 19.CONNECT WATER BY-PASS HOSE ASSEMBLY

a.

Attach the hose clamp to connect the No. 5 water by-pass hose clamp to the hose clamp bracket.


b.

Connect the water by-pass hose assembly to the upper radiator support sub-assembly with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Connect the water by-pass hose to the reservoir assembly and slide the clamp to secure the hose.


Hide 16533B 20.INSTALL NO. 1 RADIATOR SUPPORT

a.

Install the 2 radiator support cushions.


b.

Install the 2 No. 1 radiator supports with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 16697A 21.INSTALL REAR RADIATOR SIDE AIR GUIDE PLATE LH

a.

Install the rear radiator side air guide plate LH with the 2 clips.


Hide 16695A 22.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE LH

a.

Install the front radiator side air guide plate LH and attach the 3 claws.


Hide 16693A 23.INSTALL REAR RADIATOR SIDE AIR GUIDE PLATE RH

a.

Install the rear radiator side air guide plate RH with the 2 clips.


Hide 16691A 24.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE RH

a.

Install the front radiator side air guide plate RH and attach the 3 claws.


Hide 88706 25.CONNECT LIQUID TUBE SUB-ASSEMBLY (w/ Air Conditioning System)

a.

Remove the attached vinyl tape from the liquid tube sub-assembly and connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Connect the liquid tube sub-assembly to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 88703 26.CONNECT DISCHARGE HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

a.

Remove the attached vinyl tape from the discharge hose sub-assembly and connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 52131A 27.INSTALL FRONT BUMPER REINFORCEMENT

Hide 16683A 28.INSTALL LOWER RADIATOR AIR GUIDE PLATE

a.

Install the lower radiator guide plate and attach the 3 claws.


Hide 16681A 29.INSTALL UPPER RADIATOR AIR GUIDE PLATE

a.

Install the upper radiator air guide plate with 6 clips.


Hide 52029 30.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

a.

Install the front bumper upper reinforcement sub-assembly with the 2 bolts and 2 clips.

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



b.

Connect the connector to the horn.


Hide 52085 31.INSTALL FRONT BUMPER CENTER STAY SUB-ASSEMBLY

a.

Install the front bumper center stay sub-assembly with the 2 bolts.

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



b.

Connect the connector to the horn.


Hide 74414B 32.INSTALL BATTERY BRACKET REINFORCEMENT

Hide 74431 34.INSTALL BATTERY TRAY

Hide 28800 35.INSTALL BATTERY

Hide 28899 36.INSTALL BATTERY INSULATOR

Hide 52618 38.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Install the front lower bumper absorber with the 4 screws.


Hide 40.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 43.CHARGE REFRIGERANT (w/ Air Conditioning System)

Hide 44.WARM UP ENGINE (w/ Air Conditioning System)

Hide 45.INSPECT FOR REFRIGERANT LEAK (w/ Air Conditioning System)

Hide 51441 48.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 4 bolts, 2 screws and 10 clips.