Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Open in Bus 2 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 2 CAN main wires when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of central gateway ECU is 70 Ω or higher.
·

CAN main wire or connector

·

CAN branch wire or connector

·

ECM

·

Combination meter assembly

·

Central gateway ECU

·

No. 6 CAN junction connector

·

No. 7 CAN junction connector



This malfunction is not related to the lines of a bus 2 branch or to ECUs or sensors connected to a bus 2 branch.

WIRING DIAGRAM

C347339E02
1.5,3.531 5.781,3.729 4.281,0.198 10 false G172 1.51,3.688 5.792,3.885 4.281,0.198 10 false No. 7 CAN Junction Connector 2.938,1.49 4.635,1.781 1.698,0.292 10 false G171 2.938,1.646 4.875,1.958 1.938,0.313 10 false No. 6 CAN Junction Connector 6.24,1.521 7.125,1.844 0.885,0.323 10 false ECM 6,1.24 6.885,1.563 0.885,0.323 10 false CANL 5.979,0.594 6.865,0.917 0.885,0.323 10 false CANH 5.979,2.604 6.865,2.927 0.885,0.323 10 false CANH 5.99,3.24 6.875,3.563 0.885,0.323 10 false CANL 5.844,3.542 7.021,3.885 1.177,0.344 10 false G16 5.854,3.708 7.031,4.052 1.177,0.344 10 false Combination Meter Assembly 5.708,2.594 6.885,2.938 1.177,0.344 10 false 32 5.719,3.021 6.896,3.365 1.177,0.344 10 false 31 2.781,3.01 7.063,3.208 4.281,0.198 10 false 11 2.771,2.604 4.688,2.875 1.917,0.271 10 false 1 2.76,1.01 4.677,1.281 1.917,0.271 10 false 18 2.771,0.594 4.688,0.865 1.917,0.271 10 false 8 4.083,0.573 6,0.844 1.917,0.271 10 false 5 4.073,1.01 5.99,1.281 1.917,0.271 10 false 15 3.302,0.594 5.219,0.865 1.917,0.271 10 false 4 3.229,1 5.146,1.271 1.917,0.271 10 false 14 1.917,1.021 3.833,1.292 1.917,0.271 10 false 17 1.979,0.594 3.896,0.865 1.917,0.271 10 false 7 1.417,0.615 3.333,0.885 1.917,0.271 10 false 18 1.417,1 3.333,1.271 1.917,0.271 10 false 17 0.917,0.688 1.802,1.01 0.885,0.323 10 false CA4H 0.917,1.104 1.802,1.427 0.885,0.323 10 false CA4L 0.208,1.49 1.094,1.813 0.885,0.323 10 false G170 0.208,1.646 1.604,1.969 1.396,0.323 10 false Central Gateway ECU 4.688,0.677 5.573,1 0.885,0.323 10 false A62 5.135,0.688 6.021,1.01 0.885,0.323 10 false A62 5.583,0.688 6.469,1.01 0.885,0.323 10 false A61 4.677,1.104 5.563,1.427 0.885,0.323 10 false A62 5.115,1.115 6,1.438 0.885,0.323 10 false A62 5.563,1.115 6.448,1.438 0.885,0.323 10 false A61 4.677,0.479 5.563,0.802 0.885,0.323 10 false 13*1 4.677,0.917 5.563,1.24 0.885,0.323 10 false 26*1 5.125,0.917 6.01,1.24 0.885,0.323 10 false 25*2 5.115,0.49 6,0.813 0.885,0.323 10 false 26*2 5.594,0.49 6.479,0.813 0.885,0.323 10 false 7*3 5.583,0.917 6.469,1.24 0.885,0.323 10 false 6*3 0.229,4.063 4.51,4.26 4.281,0.198 10 false *1: for 2AR-FE, 3ZR-FAE, 3ZR-FE 0.229,4.396 4.51,4.594 4.281,0.198 10 false *2: for 2WW 2.51,4.042 6.792,4.24 4.281,0.198 10 false *3: for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C343209C25
3.333,0.198 3.833,0.448 0.5,0.25 2.625,0.26 2.813,0.26 2.813,0.26 3.385,0.854 true 2.583,1.604 2.771,1.604 2.771,1.604 3.417,1.031 true 2.375,0.469 2.563,0.469 2.563,0.469 3.188,0.854 true 2.417,1.365 2.604,1.365 2.604,1.365 3.229,1.01 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 2.052,0.177 2.625,0.385 0.573,0.208 10 false CANH*c 2.031,1.521 2.594,1.729 0.563,0.208 10 false CANL*c 3.417,0.229 3.875,0.427 0.458,0.198 10 false G171 1.792,0.385 2.365,0.594 0.573,0.208 10 false CANH*b 1.854,1.271 2.417,1.479 0.563,0.208 10 false CANL*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to No.7 CAN Junction Connector
*c to ECM - -



b.

Disconnect the No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G171-4 (CANH) - G171-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G171-5 (CANH) - G171-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (No. 7 CAN junction connector CAN main wire) B
NG (ECM CAN main wire) C



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

8.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the G171 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 7 CAN junction connector.

C343209C26
1.823,0.792 2.323,1.042 0.5,0.25 2.281,0.417 2.469,0.417 2.469,0.417 2.677,0.906 true 2.156,1.448 2.344,1.448 2.344,1.448 2.667,1 true 4.719,0.385 4.531,0.385 4.531,0.385 4.125,0.885 true 4.521,0.135 4.333,0.135 4.333,0.135 3.958,0.865 true 4.75,1.396 4.563,1.396 4.563,1.396 4.135,1 true 4.438,1.625 4.25,1.625 4.25,1.625 3.958,0.99 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 1.708,0.292 2.292,0.521 0.583,0.229 10 false CANH*b 4.583,0.01 5.198,0.219 0.615,0.208 10 false CANH*c 1.594,1.333 2.167,1.552 0.573,0.219 10 false CANL*b 4.51,1.5 5.125,1.708 0.615,0.208 10 false CANL*c 1.906,0.813 2.365,1.01 0.458,0.198 10 false G172 4.771,0.281 5.385,0.49 0.615,0.208 10 false CANH*d 4.813,1.26 5.427,1.469 0.615,0.208 10 false CANL*d
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Combination Meter Assembly
*c to Central Gateway ECU *d to No. 6 CAN Junction Connector



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G172-1 (CANH) - G172-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G172-7 (CANH) - G172-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G172-8 (CANH) - G172-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (No. 6 CAN junction connector CAN main wire) B
NG (Combination meter assembly CAN main wire) C
NG (Central gateway ECU CAN branch wire) D



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

C

4.CONNECT CONNECTOR

D

6.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the G172 No. 7 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
5.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)
a.
C221258C08
1.521,0.333 1.927,0.615 0.406,0.281 1.25,2 1.521,2 1.521,2 1.677,1.323 true 1.052,1.781 1.292,1.781 1.292,1.781 1.615,1.302 true 0.073,0.052 0.24,0.24 0.167,0.188 10 *a 0.635,1.688 1.063,1.844 0.427,0.156 10 CANH 0.875,1.906 1.271,2.063 0.396,0.156 10 CANL 1.583,0.375 1.906,0.563 0.323,0.188 10 G16
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-32 (CANH) - G16-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

6.CONNECT CONNECTOR
a.

Reconnect the G172 No. 7 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
7.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU)
a.
C326490C25
1.49,0.167 2.021,0.385 0.531,0.219 0.948,1.802 1.146,1.802 1.146,1.802 1.635,1.177 true 1.292,2.073 1.49,2.073 1.49,2.073 1.792,1.188 true 0.135,0.094 0.438,0.427 0.302,0.333 10 false *a 1.583,0.188 2.188,0.49 0.604,0.302 10 false G170 0.875,1.969 1.313,2.135 0.438,0.167 10 false CA4H 0.563,1.698 0.979,1.865 0.417,0.167 10 false CA4L
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-18 (CA4H) - G170-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 7 CAN JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the G171 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR OPEN IN CAN BUS WIRE (ECM)
9.CHECK FOR OPEN IN CAN BUS WIRE (ECM)
a.
C277468C02
0.521,0.219 0.938,0.479 0.417,0.26 0.188,2.563 0.604,2.823 0.417,0.26 2.24,0.51 2.406,0.51 2.406,0.51 2.521,1.146 true 2.74,2.719 2.552,2.719 2.552,2.719 2.094,3.135 true 2.406,2.531 2.219,2.531 2.219,2.531 2,3.146 true 1.594,2.021 1.75,2.021 1.75,2.021 2.427,1.229 true 2.146,2.219 2.302,2.219 2.302,2.219 2.521,1.219 true 1.01,0.25 1.427,0.448 0.417,0.198 10 false *A, *B 0.667,2.615 0.979,2.771 0.313,0.156 10 false *C 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.635,0.406 2.198,0.604 0.563,0.198 10 false CANH*A 1,2.115 2.167,2.344 1.167,0.229 10 false CANL*A, CANH*B 0.615,0.229 1.229,0.427 0.615,0.198 10 false A62 0.281,2.594 0.896,2.792 0.615,0.198 10 false A61 2.438,2.438 2.865,2.594 0.427,0.156 10 false CANL 2.792,2.625 3.24,2.802 0.448,0.177 10 false CANH 1.021,1.927 1.573,2.229 0.552,0.302 10 false CANL*B
*A for 2AR-FE, 3ZR-FAE, 3ZR-FE
*B for 2WW
*C for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2AR-FE, 3ZR-FAE, 3ZR-FE
Tester Connection Condition Specified Condition
A62-13 (CANH) - A62-26 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 2WW
Tester Connection Condition Specified Condition
A62-26 (CANH) - A62-25 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF
Tester Connection Condition Specified Condition
A61-7 (CANH) - A61-6 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM - NO. 6 CAN JUNCTION CONNECTOR)