Home › Engine / Hybrid System › CRUISE CONTROL › SPEED LIMITER SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226926 SPEED LIMITER SYSTEM J

CRUISE CONTROL  SPEED LIMITER SYSTEM  Speed Limiter System does not Operate  


DESCRIPTION

When the speed limiter is turned on using the speed limiter switch, the ECM illuminates the speed limiter indicator and activates the speed limiter system. Each function of the speed limiter system can be activated by operating the cruise control switch. When the cruise control system is operating, the speed limiter system will not operate.

WIRING DIAGRAM

B411694E05
1.583,0.802 2.51,1.177 0.927,0.375 10 false Speed Limiter Switch 0.938,2.135 2.917,2.354 1.979,0.219 10 false Steering Pad Switch Assembly 2.979,2.135 4.083,2.51 1.104,0.375 10 false Spiral Cable Sub-assembly 5.573,2.125 6.031,2.323 0.458,0.198 10 false A62 5.573,2.281 6.031,2.479 0.458,0.198 10 false ECM 5.396,0.635 6.01,0.833 0.615,0.198 10 false ASLM 5.177,0.521 5.49,0.719 0.313,0.198 10 false 49 5.396,1.604 6.01,1.802 0.615,0.198 10 false ECCS 5.948,1.594 6.26,1.792 0.313,0.198 10 false E1 2.802,0.635 3.115,0.833 0.313,0.198 10 false z1 2.802,1.594 3.115,1.792 0.313,0.198 10 false z1 4.042,0.635 4.354,0.833 0.313,0.198 10 false G8 3.125,0.542 3.74,0.74 0.615,0.198 10 false ASL 3.635,0.542 4.094,0.74 0.458,0.198 10 false ASL 3.115,1.5 3.729,1.698 0.615,0.198 10 false ECC 3.604,1.51 4.219,1.708 0.615,0.198 10 false ECC 2.365,0.542 2.979,0.74 0.615,0.198 10 false ASL 2.354,1.5 2.969,1.698 0.615,0.198 10 false ECC 2.844,0.448 3,0.646 0.156,0.198 10 false 9 2.854,1.385 3.01,1.583 0.156,0.198 10 false 7 4.063,0.438 4.375,0.635 0.313,0.198 10 false 4 4.094,1.396 4.25,1.594 0.156,0.198 10 false 2 0.135,0.052 1.604,0.292 1.469,0.24 12 false for 2WW: 5.177,1.49 5.49,1.688 0.313,0.198 10 false 42 6.198,1.49 6.354,1.688 0.156,0.198 10 false 4 4.042,1.604 4.354,1.802 0.313,0.198 10 false G8

B418222E02
0.031,0.042 2.24,0.281 2.208,0.24 12 false for 3ZR-FAE: 1.604,0.781 2.51,1.135 0.906,0.354 10 false Speed Limiter Switch 0.938,2.125 2.833,2.333 1.896,0.208 10 false Steering Pad Switch Assembly 2.958,2.115 4.031,2.49 1.073,0.375 10 false Spiral Cable Sub-assembly 5.563,2.146 6.021,2.344 0.458,0.198 10 false ECM 2.365,0.542 2.979,0.74 0.615,0.198 10 false ASL 3.125,0.542 3.74,0.74 0.615,0.198 10 false ASL 3.635,0.542 4.25,0.74 0.615,0.198 10 false ASL 5.417,0.625 6.031,0.823 0.615,0.198 10 false ASLM 5.406,1.594 6.021,1.792 0.615,0.198 10 false ECCS 5.938,1.594 6.25,1.792 0.313,0.198 10 false E1 2.333,1.521 2.792,1.719 0.458,0.198 10 false ECC 3.125,1.51 3.583,1.708 0.458,0.198 10 false ECC 3.625,1.51 4.083,1.708 0.458,0.198 10 false ECC 5.042,0.635 5.656,0.833 0.615,0.198 10 false A62 5.042,1.604 5.656,1.802 0.615,0.198 10 false A62 6.229,1.594 6.844,1.792 0.615,0.198 10 false B93 6.281,1.385 6.594,1.583 0.313,0.198 10 false 59 5.094,1.396 5.406,1.594 0.313,0.198 10 false 35 5.094,0.438 5.406,0.635 0.313,0.198 10 false 20 4.042,0.635 4.354,0.833 0.313,0.198 10 false G8 4.052,1.604 4.365,1.802 0.313,0.198 10 false G8 2.802,1.594 3.115,1.792 0.313,0.198 10 false z1 2.813,0.635 3.125,0.833 0.313,0.198 10 false z1 4.083,0.448 4.24,0.646 0.156,0.198 10 false 4 4.094,1.396 4.25,1.594 0.156,0.198 10 false 2 2.844,0.427 3,0.625 0.156,0.198 10 false 9 2.844,1.396 3,1.594 0.156,0.198 10 false 7

PROCEDURE

1.CHECK CRUISE CONTROL SYSTEM
a.

Turn the ignition switch ON.


b.

Turn the cruise control on using the cruise control switch.


c.

Check the operation of each function by operating the cruise control switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>ROAD TEST


OK:

Each function of the cruise control system operates normally.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (ASL MAIN SWITCH)

NG

2.READ VALUE USING GTS (ASL MAIN SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

for 2WW:

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

for 2WW:

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ASL Main SW Speed limiter switch signal ON or OFF ON: Speed limiter switch on
OFF: Speed limiter switch off
-
Powertrain > Engine and ECT > Data List
Tester Display
ASL Main SW
50003 371 210

f.

for 3ZR-FAE:

Enter the following menus : Powertrain / Cruise Control / Data List / ASL Main Switch.


g.

for 3ZR-FAE:

According to the display on the GTS, read the Data List.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ASL Main Switch Speed limiter switch signal ON or OFF ON: Speed limiter switch on
OFF: Speed limiter switch off
-
Powertrain > Cruise Control > Data List
Tester Display
ASL Main Switch
50003 237 32

OK:

The GTS display changes according to switch operation.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
a.

Disconnect the A62 ECM connector.


b.

Disconnect the G8 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2WW
Tester Connection Condition Specified Condition
A62-49 (ASLM) - G8-4 (ASL) Always Below 1 Ω
A62-42 (ECCS) - G8-2 (ECC) Always Below 1 Ω
A62-49 (ASLM) or G8-4 (ASL) - Body ground Always 10 kΩ or higher
A62-42 (ECCS) or G8-2 (ECC) - Body ground Always 10 kΩ or higher


for 3ZR-FAE
Tester Connection Condition Specified Condition
A62-20 (ASLM) - G8-4 (ASL) Always Below 1 Ω
A62-35 (ECCS) - G8-2 (ECC) Always Below 1 Ω
A62-20 (ASLM) or G8-4 (ASL) - Body ground Always 10 kΩ or higher
A62-35 (ECCS) or G8-2 (ECC) - Body ground Always 10 kΩ or higher


Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the A62*1 or B93*2 ECM connector.

*1: for 2WW

*2: for 3ZR-FAE



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2WW
Tester Connection Condition Specified Condition
A62-4 (E1) - Body ground Always Below 1 Ω

for 3ZR-FAE
Tester Connection Condition Specified Condition
B93-59 (E1) - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

6.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

6.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STEERING PAD SWITCH