Home › Drivetrain › K114F MULTIDRIVE / CVT › TRANSMISSION CONTROL CABLE › from 2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0172319 TRANSMISSION CONTROL CABLE A

K114F MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C296270

Install the transmission control cable assembly to the body with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
C316613

Install the transmission control cable assembly to rear engine mounting insulator with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.
C296306

Install the transmission control cable assembly to the transmission control cable support with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


d.
C300679C01
3.188,0.979 3.375,1.146 0.188,0.167 10 true *a 2.854,0.375 3.031,0.521 0.177,0.146 10 true *b
*a P Position
*b N Position


Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.


e.
C296239

Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


f.

Install the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper to lock the nut.

C328348C01
1.49,0.563 1.365,0.271 1.365,0.271 0.906,0.271 true 1.521,1.115 1.708,1.396 1.708,1.396 1.917,1.396 false 0.719,0.177 1.031,0.375 0.313,0.198 10 false *1 1.99,1.313 2.302,1.51 0.313,0.198 10 false *2
*1 Stopper *2 Nut
V113147

Turn in this Direction
V113148

Push in this Direction


NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.


HINT:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.



b.

Install the outer part of the transmission control cable assembly to the shift lever assembly. Check that the stopper returns to the pulled out position.

C328349C01
0.615,0.219 0.948,0.219 0.948,0.219 1.198,0.344 true 0.771,1.448 1.042,1.448 1.042,1.448 1.208,0.844 true 1.052,1.604 1.271,1.604 1.271,1.604 1.333,1.271 true 0.417,0.135 0.729,0.333 0.313,0.198 10 false *1 0.573,1.354 0.885,1.552 0.313,0.198 10 false *2 0.875,1.521 1.188,1.719 0.313,0.198 10 false *3
*1 Stopper *2 Nut
*3 Shift Lever Assembly - -
V113147

Install in this Direction - -



c.
C328343C02
1.073,0.292 1.365,0.292 1.365,0.292 1.75,1.021 true 2.292,1.125 2.51,1.417 2.51,1.417 2.76,1.417 true 2.26,2.083 2.26,1.813 2.26,1.813 2.646,1.813 false 1.177,1.854 1.708,1.854 1.708,1.854 1.823,2.219 false 0.885,0.198 1.198,0.396 0.313,0.198 10 false *1 2.844,1.333 3.156,1.531 0.313,0.198 10 false *2 2.719,1.719 3.031,1.917 0.313,0.198 10 false *2 0.99,1.76 1.302,1.958 0.313,0.198 10 false *1
*1 Slider
*2 Lock Piece
V113147

Slide in this Direction
V113148

Pull in this Direction


Slide the slider in the direction shown in the illustration and pull out the lock piece.


d.
C328345C01
2.01,1.438 2.115,1.333 false
V113147

Connect in this Direction


Connect the end of the transmission control cable assembly to the shift lever assembly.

NOTICE:
·

Make sure that the lock piece is pulled up.

·

Push on the end of the transmission control cable assembly all the way to the base of the pin.




e.
C328344C02
0.188,0.646 0.188,0.156 0.188,0.156 0.969,0.156 true 1.021,0.073 1.333,0.271 0.313,0.198 10 true *1
*1 Cable Rod
V113147

Push in this Direction


Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.


f.

Push the lock piece into the adjuster case and lock it.

NOTICE:

Make sure that the lock piece is completely locked by the slider.



Hide 58910C 5.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 50819 7.INSTALL FRONT FLOOR COVER

Hide 74414B 8.INSTALL BATTERY BRACKET REINFORCEMENT

Hide 74411B 9.INSTALL FRONT BATTERY BRACKET

Hide 16057 10.CONNECT RADIATOR HOSE SUB-ASSEMBLY

Hide 74431 11.INSTALL BATTERY TRAY

Hide 28800 12.INSTALL BATTERY

Hide 74404A 13.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 14.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 15.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 17705 16.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 11212 17.INSTALL NO. 2 CYLINDER HEAD COVER

Hide 18.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION