When an incorrect ECM, an incorrect brake actuator assembly or an incorrect main body ECU is installed after the assist map has been written in the power steering ECU assembly, then DTC C1582/26 is stored because the data does not match the vehicle specifications.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition |
|---|---|---|---|---|---|
| C1582/26 | Assist Map Number Mismatch | Assist map number mismatch | ·
CAN communication system ·
Incorrect ECM ·
Incorrect skid control ECU (brake actuator assembly) ·
Incorrect main body ECU (multiplex network body ECU) ·
Power steering ECU assembly |
Off | Assist map written |
If the power steering ECU assembly has been replaced, perform assist map writing (Click here Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).
Check for DTCs.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC is not output |
| DTC is output |
DTC is not output
DTC is output
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
Check if any of the parts listed below have been replaced with an incorrect part in the past.
| Related Part | ECM |
| Main body ECU (multiplex network body ECU) | |
| Skid control ECU (brake actuator assembly) |
When removing a related part to check it, be sure to follow the appropriate procedures and precautions.
Refer to the following procedures to remove the ECM (for 2WW).
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL
Refer to the following procedures to remove the ECM (for 2AD-FHV).
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
Refer to the following procedures to remove the ECM (for 2AD-FTV).
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
Refer to the following procedures to remove the ECM (for 2AR-FE).
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
Refer to the following procedures to remove the ECM (for 3ZR-FAE).
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
Refer to the following procedures to remove the ECM (for 3ZR-FE).
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
Refer to the following procedures to remove the main body ECU (multiplex network body ECU) (for LHD).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
Refer to the following procedures to remove the main body ECU (multiplex network body ECU) (for RHD).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Refer to the following procedures to remove the skid control ECU (brake actuator assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL
DTC C1582/26 is stored when a part with an incorrect part number is installed for the related parts listed above.
When DTC C1582/26 is output when parts have not been exchanged, replace the power steering ECU assembly as it may have an internal malfunction.
| Proceed to |
|---|
| All installed related parts have correct part number |
| Part with incorrect part number is installed |
All installed related parts have correct part number
Part with incorrect part number is installed