Home › Engine / Hybrid System › 3ZR-FAE LUBRICATION › OIL PUMP › from 2015.10
RM3090E _51 Engine / Hybrid System _008392 3ZR-FAE LUBRICATION _0046846 OIL PUMP A

3ZR-FAE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 22210 3.REMOVE THROTTLE BODY ASSEMBLY

Hide 6.REMOVE WIRE HARNESS CLAMP BRACKET

Hide 23901 7.REMOVE FUEL TUBE SUB-ASSEMBLY

Hide 23807 8.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23250 9.REMOVE FUEL INJECTOR ASSEMBLY

Hide 11452 10.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17167 11.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 29300 14.REMOVE VACUUM PUMP ASSEMBLY

Hide 16267 16.DISCONNECT NO. 3 WATER BY-PASS HOSE

Hide 16261 17.REMOVE WATER BY-PASS HOSE

Hide 16262 18.DISCONNECT WATER INLET HOSE

Hide 16321 19.REMOVE WATER INLET

Hide 16331A 20.REMOVE THERMOSTAT

Hide 12551A 22.REMOVE NO. 1 VACUUM PUMP BRACKET

Hide 16620 23.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11201 24.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11213 25.REMOVE CYLINDER HEAD COVER GASKET

Hide 26.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13540 28.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 30.REMOVE ENGINE MOUNTING BRACKET STUD BOLT

Hide 11302 31.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A348609

Remove the 3 bolts and engine mounting bracket RH.


b.
A348610

Remove the 4 bolts and oil filter bracket.


c.
A348611

Remove the 2 O-rings.


d.
A348612C01
0.615,3.115 0.844,3.115 0.844,3.115 1.615,1.781 true 0.427,3.021 0.625,3.229 0.198,0.208 10 false *1
*1 Seal Washer


Remove the 19 bolts and seal washer.


e.
A348613C01
0.563,0.396 1.094,0.25 1.094,0.25 1.25,0.25 true 2.74,1.885 2.938,0.698 2.938,0.698 3.094,0.698 true 2.76,4.042 2.938,3.323 2.938,3.323 3.094,3.323 true 0.542,3.823 1.01,4.198 1.01,4.198 1.167,4.198 true 3.135,0.594 3.323,0.802 0.188,0.208 10 false *a 1.292,0.146 1.479,0.354 0.188,0.208 10 false *a 1.198,4.094 1.385,4.302 0.188,0.208 10 false *a 3.125,3.219 3.313,3.427 0.188,0.208 10 false *a
*a Protective Tape


Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly with a screwdriver as shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and timing chain cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



f.
A175207

Remove the 3 O-rings.


g.
A350777

Remove the 3 bolts and engine water pump assembly.


h.
A350778

Remove the gasket.


Hide 11302A 32.REMOVE TIMING CHAIN COVER OIL SEAL

a.
A199941C02
0.698,0.479 1.031,0.479 1.031,0.479 1.615,1.313 true 2.833,1.667 3.083,1.667 3.083,1.667 2.333,2.083 true 0.469,0.385 0.667,0.552 0.198,0.167 10 *1 3.135,1.573 3.333,1.75 0.198,0.177 10 *2
*1 Protective Tape
*2 Wooden Block


Place the timing chain cover sub-assembly on wooden blocks.


b.

Using a screwdriver, tap out the timing chain cover oil seal.

NOTICE:

Do not damage the surface of the timing chain cover oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.



Hide 13559 33.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 34.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13521 36.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A150878

Remove the crankshaft timing sprocket.


Hide 13507 37.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

a.
A206155E01
0.337,0.148 0.66,0.325 0.323,0.177 10 SST 0.724,0.216 0.87,0.216 0.87,0.216 1.48,0.474 false 1.189,0.587 0.87,0.216 false

Temporarily install the crankshaft pulley and crankshaft pulley bolt.


b.

Using SST, hold the crankshaft. Then remove the drive shaft gear nut.

SST
09213-54015  09330-00021  

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-00850 (quantity: 2)



c.

Remove SST, the crankshaft pulley bolt and the crankshaft pulley.


d.
A150873

Remove the bolt, chain tensioner plate and chain damper spring.


e.
A150877C07
0.948,1.625 1.073,1.625 1.073,1.625 1.24,1.854 false 1.51,1.281 1.635,1.281 1.635,1.281 1.802,1.51 false 1.417,2.563 1.552,2.563 1.552,2.563 1.708,2.792 false 0.74,1.521 0.958,1.677 0.219,0.156 10 *1 1.219,2.479 1.438,2.635 0.219,0.156 10 *2 1.313,1.188 1.521,1.354 0.208,0.167 10 *3
*1 Oil Pump Drive Gear
*2 Oil Pump Drive Shaft Gear
*3 No. 2 Chain Sub-assembly


Remove the oil pump drive gear, oil pump drive shaft gear and No. 2 chain sub-assembly.


Hide 12102A 38.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A150894

Remove the 10 bolts and 2 nuts.


b.
A120816

Insert the blade of a oil pan seal cutter between the stiffening crankcase and No. 2 oil pan sub-assembly. Cut through the sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the surface of the oil pan which contacts the stiffening crankcase.

·

Be careful not to damage the stiffening crankcase flange.




Hide 15100 39.REMOVE OIL PUMP ASSEMBLY

a.
A173460

Remove the 3 bolts and oil pump assembly.