Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Entry and Start System) › from 2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048166 IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

1. for 3ZR Series Engine


B341473E15
2,1.156 2.448,1.406 0.448,0.25 10 false 29*1 2,1.344 2.385,1.51 0.385,0.167 10 false 45*2 2.01,0.406 2.396,0.573 0.385,0.167 10 false 28 1.667,0.469 2.052,0.635 0.385,0.167 10 false IMO 1.708,1.229 2.094,1.396 0.385,0.167 10 false IMI 5.438,0.375 5.667,0.552 0.229,0.177 10 false 12 5.438,1.125 5.667,1.302 0.229,0.177 10 false 13 5.719,0.49 6.104,0.656 0.385,0.167 10 false EFII 5.729,1.24 6.115,1.406 0.385,0.167 10 false EFIO 1.219,1.958 1.885,2.135 0.667,0.177 10 false A62 1.281,2.115 2.146,2.302 0.865,0.188 10 false ECM 2.948,1.667 4.688,1.844 1.74,0.177 10 false *1: for K111, K111F 2.969,1.917 4.969,2.094 2,0.177 10 false *2: except K111, K111F 5.594,1.99 5.979,2.156 0.385,0.167 10 false G88 5.594,2.156 6.74,2.323 1.146,0.167 10 false Transponder Key ECU Assembly


2. except 3ZR Series Engine


B341473E16
2,1.135 3.573,1.427 1.573,0.292 10 false 28*1, 34*2 1.99,1.333 2.375,1.5 0.385,0.167 10 false 16*3 2,0.396 2.802,0.594 0.802,0.198 10 false 29*1, 44*2 2,0.594 2.385,0.76 0.385,0.167 10 false 15*3 1.667,0.469 2.052,0.635 0.385,0.167 10 false IMO 1.708,1.229 2.094,1.396 0.385,0.167 10 false IMI 5.438,0.375 5.667,0.552 0.229,0.177 10 false 12 5.438,1.125 5.667,1.302 0.229,0.177 10 false 13 5.719,0.49 6.104,0.656 0.385,0.167 10 false EFII 5.729,1.24 6.115,1.406 0.385,0.167 10 false EFIO 1.281,1.979 1.948,2.156 0.667,0.177 10 false A62*1, *2 1.281,2.125 2.01,2.292 0.729,0.167 10 false A61*3 1.281,2.281 2.146,2.469 0.865,0.188 10 false ECM 2.948,1.667 4.146,1.865 1.198,0.198 10 false *1: for 2AR-FE 2.969,1.917 4.167,2.115 1.198,0.198 10 false *2: for 2WW 5.594,1.99 5.979,2.156 0.385,0.167 10 false G88 5.594,2.156 6.74,2.323 1.146,0.167 10 false Transponder Key ECU Assembly 2.969,2.167 4.75,2.406 1.781,0.24 10 false *3: for 2AD-FHV, 2AD-FTV


CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 61
Body Electrical > Immobiliser > Clear DTCs
50002 260
Body Electrical > Telematics > Clear DTCs
50002 233

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 61
Powertrain > Engine > Trouble Codes
50001 61
Body Electrical > Immobiliser > Trouble Codes
50001 260
Body Electrical > Telematics > Trouble Codes
50001 233
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
DTCs are not output (for Gasoline)
DTCs are not output (for Diesel)
DTCs are output



DTCs are not output (for Gasoline)

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

DTCs are not output (for Diesel)

4.CHECK WHETHER ENGINE STARTS

DTCs are output

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Engine and ECT / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut OFF/ON - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 61 681
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK (for 2AR-FE [w/ Canister Pump Module])
OK (for 2AR-FE [w/o Canister Pump Module])
OK (for 3ZR-FAE)
OK (for 3ZR-FE [for K111, K111F])
OK (for 3ZR-FE [except K111, K111F])
NG



OK (for 2AR-FE [w/ Canister Pump Module])

OK (for 2AR-FE [w/o Canister Pump Module])

OK (for 3ZR-FAE)

OK (for 3ZR-FE [for K111, K111F])

OK (for 3ZR-FE [except K111, K111F])

NG

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.


Result:
Proceed to
Engine can be started
Engine cannot be started



Engine can be started

Engine cannot be started

5.REGISTER ECU COMMUNICATION ID
5.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.


Result:
Proceed to
Engine can be started
Engine cannot be started



Engine can be started

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

Engine cannot be started

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the A62*1, *2, *3 or A61*4 ECM connector.

*1: for 3ZR (for K111, K111F), 2AR-FE

*2: for 3ZR (except K111, K111F)

*3: for 2WW

*2: for 2AD-FHV, 2AD-FTV



c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
for 3ZR (for K111, K111F), 2AR-FE
Tester Connection Condition Specified Condition
G88-12 (EFII) - A62-29 (IMO) Always Below 1 Ω
A62-29 (IMO) - Body ground Always 10 kΩ or higher
G88-12 (EFII) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - A62-28 (IMI) Always Below 1 Ω
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground Always 10 kΩ or higher

for 3ZR (except K111, K111F)
Tester Connection Condition Specified Condition
G88-12 (EFII) - A62-45 (IMO) Always Below 1 Ω
A62-45 (IMO) - Body ground Always 10 kΩ or higher
G88-12 (EFII) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - A62-28 (IMI) Always Below 1 Ω
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground Always 10 kΩ or higher

for 2WW
Tester Connection Condition Specified Condition
G88-12 (EFII) - A62-44 (IMO) Always Below 1 Ω
A62-44 (IMO) - Body ground Always 10 kΩ or higher
G88-12 (EFII) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - A62-34 (IMI) Always Below 1 Ω
A62-34 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground Always 10 kΩ or higher

for 2AD-FHV, 2AD-FTV
Tester Connection Condition Specified Condition
G88-12 (EFII) - A61-15 (IMO) Always Below 1 Ω
A61-15 (IMO) - Body ground Always 10 kΩ or higher
G88-12 (EFII) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - A61-16 (IMI) Always Below 1 Ω
A61-16 (IMI) - Body ground Always 10 kΩ or higher
G44-4 (EFIO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)
NG (for 2WW)
NG (for 2AD-FTV)
NG (for 2AD-FHV)



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

NG (for 2WW)

NG (for 2AD-FTV)

NG (for 2AD-FHV)