Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR › 2015.10–2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0230681 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C344847N01
2.396,2.698 2.552,2.896 0.156,0.198 10 true A 0.99,2.75 1.146,2.948 0.156,0.198 10 true B 1.969,2.948 2.125,3.146 0.156,0.198 10 true C

Install the brake actuator with bracket with the 3 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Tighten the 3 nuts uniformly in alphabetical order.

·

Be careful not to damage the brake tubes.




b.

Connect the 3 clamps to the brake actuator bracket assembly.


c.
C317498C01
0.646,0.698 1.292,0.698 true 0.656,1.052 1.135,1.052 1.135,1.052 1.49,0.708 true 0.688,1.406 1.073,1.406 1.073,1.406 1.51,0.948 true 2.063,0.885 2.292,1.24 2.292,1.24 2.573,1.24 true 1.719,0.667 2.104,0.219 2.104,0.219 2.406,0.219 true 1.927,0.656 2.26,0.417 2.26,0.417 2.563,0.417 true 2.635,0.344 2.948,0.542 0.313,0.198 10 true *a 0.5,0.604 0.708,0.833 0.208,0.229 10 true *b 0.521,0.969 0.708,1.208 0.188,0.24 10 true *c 2.438,0.125 2.604,0.365 0.167,0.24 10 true *d 2.615,1.146 2.823,1.396 0.208,0.25 10 true *e 0.521,1.333 0.708,1.563 0.188,0.229 10 true *f
*a To Front Wheel Cylinder RH
*b To Front Wheel Cylinder LH
*c To Rear Wheel Cylinder RH
*d To Rear Wheel Cylinder LH
*e From Front Master Cylinder
*f From Rear Master Cylinder


Temporarily install each brake line to the correct positions of the brake actuator assembly with bracket as shown in the illustration.


d.
C310275C01
2.042,0.115 2.354,0.313 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, tighten each 6 brake lines.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




e.
C306193

Connect the clamp to the brake actuator bracket assembly.


f.

Connect the wire harness connector to the brake actuator assembly, and then push up the lock lever to apply the lock.

NOTICE:
·

Before connecting the wire harness connector, make sure that the surfaces of the wire harness connector are free of foreign matter.

·

After connecting the wire harness connector, make sure that the lock lever is securely locked.




Hide 3.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 4.BLEED BRAKE SYSTEM