Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise SET Indicator Light Circuit  


DESCRIPTION

·

The ECM turns on the cruise control SET indicator by sending indicator output demand signals to the combination meter assembly using CAN communication.

·

The cruise control SET indicator illuminates when the dynamic radar cruise control system is controlling vehicle speed.

·

The cruise control SET indicator circuit uses CAN communication. If the cruise control SET indicator is not functioning correctly, check for CAN communication system before troubleshooting this circuit.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (METER DISPLAY 1)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All -
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7
OK:

The multi-information display turns on or off according to the operation of the Active Test.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (-SET SWITCH)

NG

2.READ VALUE USING GTS (-SET SWITCH)
a.

Turn the dynamic radar cruise control system on using the cruise control switch (ON/OFF).


b.

Drive at a speed between approximately 40 km/h or 25 mph and 200 km/h or 125 mph.


c.

Enter the following menus: Powertrain / Radar Cruise1 / Data List.


d.

Read the Data List according to the display on the GTS.

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SET/COAST Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
Powertrain > Radar Cruise1 > Data List
Tester Display
SET/COAST Switch
50003 74 21

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
-SET Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
Powertrain > Radar Cruise1 > Data List
Tester Display
-SET Switch
50003 239 116

iii.

for 2WW:

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
-SET SW -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
Powertrain > Cruise Control > Data List
Tester Display
-SET SW
50003 391 13


Result:
Result Proceed to
The cruise control SET indicator illuminates and turns off according to the operation of the cruise control switch (-SET switch). A
The cruise control SET indicator does not illuminate but the Data List item -SET Switch changes according to the operation of the cruise control switch (-SET switch). B
The cruise control SET indicator does not illuminate and the Data List item -SET Switch does not change according to the operation of the cruise control switch (-SET switch). C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C