Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

This circuit sends a signal to the ECM depending on the cruise control switch condition. The battery supplies positive (+) battery voltage to the circuit control main switch. Then terminal CCS of the ECM receives the voltage according to the switch condition.

WIRING DIAGRAM

C350493E06
5.604,0.521 6.031,0.75 0.427,0.229 10 false A62 5.229,0.521 5.656,0.75 0.427,0.229 10 false A62 4.875,0.521 5.219,0.76 0.344,0.24 10 false A62 4.51,0.521 5.042,0.76 0.531,0.24 10 false A61 6.333,0.5 6.802,0.74 0.469,0.24 10 false CCS 5.615,2.594 5.927,2.813 0.313,0.219 10 false A62 6.344,2.594 6.854,2.823 0.51,0.229 10 false ECCS 4.542,0.292 4.865,0.542 0.323,0.25 10 false 23 4.917,0.292 5.219,0.448 0.302,0.156 10 false 40 5.281,0.292 5.51,0.469 0.229,0.177 10 false 60 5.635,0.292 5.896,0.49 0.26,0.198 10 false 41 5.656,2.365 5.948,2.552 0.292,0.188 10 false 42 4.667,1.688 4.906,1.865 0.24,0.177 10 false G8 4.677,2.594 4.917,2.771 0.24,0.177 10 false G8 3.667,2.573 3.906,2.75 0.24,0.177 10 false z4 3.667,1.667 3.906,1.844 0.24,0.177 10 false z4 2.938,2.813 3.844,3.375 0.906,0.563 10 false Cruise Control Switch Wire 3.896,3.073 5,3.469 1.104,0.396 10 false Spiral Cable Sub-assembly 4.708,1.458 4.917,1.646 0.208,0.188 10 false 1 4.74,2.365 4.948,2.552 0.208,0.188 10 false 2 3.708,1.458 3.917,1.646 0.208,0.188 10 false 3 3.708,2.365 3.917,2.552 0.208,0.188 10 false 4 2.938,2.479 3.146,2.667 0.208,0.188 10 false 1 2.958,1.573 3.167,1.76 0.208,0.188 10 false 3 4.104,1.823 4.573,2.031 0.469,0.208 10 false CCS 4.083,2.719 4.51,2.896 0.427,0.177 10 false ECC 2.469,2.021 2.823,2.385 0.354,0.365 10 false ON-OFF 2.531,1.594 2.958,1.844 0.427,0.25 10 false CCS 2.521,2.698 2.948,2.875 0.427,0.177 10 false ECC 1.875,2.135 2.344,2.385 0.469,0.25 10 false +RES 1.292,2.115 1.74,2.323 0.448,0.208 10 false -SET 0.5,2.094 1.146,2.292 0.646,0.198 10 false CANCEL 0.823,3.094 1.031,3.281 0.208,0.188 10 false A 0.813,3.26 2.76,3.469 1.948,0.208 10 false Cruise Control Switch 0.115,3.802 2.552,3.99 2.438,0.188 10 false *1: for 2AD-FHV, 2AD-FTV 0.125,4.104 4.115,4.302 3.99,0.198 10 false *2: for 2AR-FE 0.125,4.427 2.281,4.656 2.156,0.229 10 false *3: for 3ZR-FE (for K111, K111F) 0.125,5.094 3.094,5.323 2.969,0.229 10 false *5: for 3ZR-FAE, 3ZR-FE (except K111, K111F) 0.125,4.75 1.688,4.958 1.563,0.208 10 false *4: for 2WW 6.438,3.875 6.865,4.052 0.427,0.177 10 false ECM 6.01,0.75 6.219,0.938 0.208,0.188 10 false *5 5.677,2.823 5.885,3.01 0.208,0.188 10 false *4 4.552,0.75 4.76,0.938 0.208,0.188 10 false *1 4.917,0.75 5.125,0.938 0.208,0.188 10 false *2 5.281,0.75 5.49,0.938 0.208,0.188 10 false *3 5.646,0.75 5.854,0.938 0.208,0.188 10 false *4 5.969,0.521 6.396,0.75 0.427,0.229 10 false A62 6,0.292 6.26,0.49 0.26,0.198 10 false 36 5.969,2.594 6.281,2.813 0.313,0.219 10 false A62 6.01,2.365 6.302,2.552 0.292,0.188 10 false 35 6.01,2.823 6.219,3.01 0.208,0.188 10 false *5 0.125,5.406 3.813,5.656 3.688,0.25 10 false *6: except 2WW, 3ZR-FAE, 3ZR-FE (for K111, K111F) 5.313,3.094 5.521,3.281 0.208,0.188 10 false *6

PROCEDURE

1.READ VALUE USING GTS
a.

Check the Data List for proper functioning of the cruise control switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control switch signal (Main CPU) ON or OFF ON: Cruise control switch on
OFF: Cruise control switch off
-
Cancel Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch +RES switch signal ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Powertrain > Radar Cruise1 > Data List
Tester Display
Main SW M-CPU
Cancel Switch
SET/COAST Switch
RES/ACC Switch
50003 74 17,20,21,22
OK:

When the cruise control switch is operated, the display changes as shown above.



ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES Switch +RES switch status ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Ready Main-CPU Cruise control system standby condition ON or OFF Each time cruise control switch is pushed, ON or OFF changes -
Cruise Ready Sub-CPU Cruise control system standby condition ON or OFF Each time cruise control switch is pushed, ON or OFF changes -
Powertrain > Radar Cruise1 > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Ready Main-CPU
Cruise Ready Sub-CPU
50003 239 117,116,115,113,114
OK:

When the cruise control switch is operated, the display changes as shown above.



iii.

for 2WW:

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CANCEL SW CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET SW -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES SW +RES switch signal ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Control Switch Cruise control switch signal ON or OFF ON: Cruise control switch (ON/OFF) pushed
OFF: Cruise control switch (ON/OFF) released
-
Powertrain > Cruise Control > Data List
Tester Display
CANCEL SW
-SET SW
+RES SW
Cruise Control Switch
50003 391 14,13,12,8
OK:

When the cruise control switch is operated, the display changes as shown above.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL SWITCH
2.INSPECT CRUISE CONTROL SWITCH
a.

b.

Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.

Disconnect the z4 spiral cable sub-assembly connector.


b.

Disconnect the A cruise control switch wire connector.


c.
E178683C12
0.292,0.729 0.729,1.042 0.438,0.313 0.24,2.385 0.677,2.698 0.438,0.313 1.656,1.542 1.281,1.094 true 0.656,1.542 1.073,1.125 true 0.583,3.073 1,2.656 true 1.813,3.094 1.438,2.646 true 0.146,0.313 0.458,0.51 0.313,0.198 10 false *a 0.24,1.969 0.552,2.167 0.313,0.198 10 false *b 0.417,2.458 0.573,2.656 0.156,0.198 10 false A 0.438,0.823 0.75,1.021 0.313,0.198 10 false z4 1.573,1.583 2.031,1.781 0.458,0.198 10 false ECC 0.49,1.552 0.948,1.75 0.458,0.198 10 false CCS 0.417,3.104 0.875,3.302 0.458,0.198 10 false ECC 1.698,3.125 2.156,3.323 0.458,0.198 10 false CCS
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-3 (CCS) - A-3 (CCS) Always Below 1 Ω
z4-4 (ECC) - A-1 (ECC) Always Below 1 Ω
z4-3 (CCS) or A-3 (CCS) - Body ground Always 10 kΩ or higher
z4-4 (ECC) or A-1 (ECC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

for 2AD-FHV, 2AD-FTV:

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the A61 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 (CCS) - A61-23 (CCS) Always Below 1 Ω
G8-2 (ECC) - Body ground Always Below 1 Ω
G8-1 (CCS) or A61-23 (CCS) - Body ground Always 10 kΩ or higher




b.

for 2AR-FE:

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the A62 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 (CCS) - A62-40 (CCS) Always Below 1 Ω
G8-2 (ECC) - Body ground Always Below 1 Ω
G8-1 (CCS) or A62-40 (CCS) - Body ground Always 10 kΩ or higher




c.

for 3ZR-FE (for K111, K111F):

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the A62 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 (CCS) - A62-60 (CCS) Always Below 1 Ω
G8-2 (ECC) - Body ground Always Below 1 Ω
G8-1 (CCS) or A62-60 (CCS) - Body ground Always 10 kΩ or higher




d.

for 3ZR-FAE, 3ZR-FE (except K111, K111F):

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the A62 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 (CCS) - A62-36 (CCS) Always Below 1 Ω
G8-2 (ECC) - A62-35 (ECCS) Always Below 1 Ω
G8-1 (CCS) or A62-36 (CCS) - Body ground Always 10 kΩ or higher




e.

for 2WW:

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the A62 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 (CCS) - A62-41 (CCS) Always Below 1 Ω
G8-2 (ECC) - A62-42 (ECCS) Always Below 1 Ω
G8-1 (CCS) or A62-41 (CCS) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR