Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2016.08
RM3090E _52 Drivetrain _008762 AXLE AND DIFFERENTIAL _0049345 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502C 1.INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH

a.

Secure the steering knuckle in a vise.

NOTICE:

When using a vise, do not overtighten it.



b.

Install the front brake dust cover to the steering knuckle.


c.

Install the front axle hub sub-assembly with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)

NOTICE:

Do not place the hub and bearing's magnet rotor side so that it is facing downward, and do not allow the magnet rotor side to become damaged or contact foreign matter.



Hide 2.INSTALL FRONT AXLE ASSEMBLY LH

a.
C159694C02
1.813,1.188 2.792,1.385 false 1.844,1.333 2.792,1.396 false 2.906,1.313 3.219,1.469 0.313,0.156 10 *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.


b.
C357235

Apply MP grease to the entire contact surface between the front drive shaft assembly and axle hub bearing surface or only apply 0.1 to 0.3 g (0.00353 to 0.0105 oz.) of MP grease to the 4 areas on the axle hub bearing shown in the illustration.


c.

Install the front axle assembly to the front shock absorber assembly with coil spring with the 2 bolts and 2 nuts.

Torque:
240 N*m (2447 kgf*cm, 177 ft.*lbf)

NOTICE:
·

Be careful not to damage the drive shaft boot and speed sensor rotor.

·

Do not tighten the bolts.




Hide 48069 3.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 45047 4.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 6.CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.

Connect the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
106.8 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 43502H 7.TEMPORARILY INSTALL FRONT AXLE SHAFT NUT LH

a.

Clean the threaded parts on the drive shaft and a new axle shaft nut using a non-residue solvent.

NOTICE:
·

Be sure to perform this work for a new drive shaft.

·

Keep the threaded parts free of oil and foreign objects.




b.
C164699

Using a 30 mm socket wrench, temporarily install a new axle shaft nut.

Torque:
for Axle Hub Spline Diameter 26 mm (1.02 in.) : 216 N*m (2203 kgf*cm, 159 ft.*lbf)
for Axle Hub Spline Diameter 30 mm (1.18 in.) : 292 N*m (2978 kgf*cm, 215 ft.*lbf)

HINT:

Stake the nut after inspecting for looseness and runout in the following steps.



Hide 8.DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

Hide 10.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 43512 12.INSTALL FRONT DISC

Hide 13.CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.

Connect the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
106.8 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 47313A 14.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose to the steering knuckle with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 89543 15.CONNECT FRONT SPEED SENSOR LH

a.

Connect the front speed sensor and front flexible hose to the front shock absorber with the bolt and clamp.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.


HINT:

Install the front flexible hose first and then the speed sensor harness bracket.



b.

Install the front speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.



Hide 43502H 16.INSTALL FRONT AXLE SHAFT NUT LH

a.
C129484

Using a chisel and hammer, stake the front axle shaft nut.


Hide 17.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 18.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT