There may be a short circuit between the bus 2 CAN main wires and/or CAN branch wires when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU is below 54 Ω.
| Detection Item | Trouble Area |
|---|---|
|
*1: w/ Entry and Start System *2: for 4WD/AWD *3: w/ Stop and Start System |
|
| Resistance between terminals 18 (CA4H) and 17 (CA4L) of central gateway ECU is below 54 Ω. | ·
Short in bus 2 CAN main wires ·
Short in bus 2 CAN branch wires ·
ECM ·
Combination meter assembly ·
Central gateway ECU ·
Power steering ECU assembly ·
Air conditioning amplifier assembly ·
Airbag sensor assembly ·
Spiral with sensor cable sub-assembly (steering angle sensor) ·
Certification ECU (smart key ECU assembly)*1 ·
4WD ECU assembly*2 ·
Brake actuator assembly (skid control ECU) ·
Main body ECU (multiplex network body ECU) ·
Engine stop and start ECU*3 ·
No. 11 CAN junction connector ·
No. 12 CAN junction connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
| *a | Rear view of wire harness connector
(to No. 11 CAN Junction Connector) |
*b | to Main Body ECU (Multiplex Network Body ECU) |
| *c | to Air Conditioning Amplifier Assembly | *d | to Brake Actuator Assembly (Skid Control ECU) |
| *e | to No. 12 CAN Junction Connector | *f | to Engine Stop and Start ECU (w/ Stop and Start System) |
| *g | to Airbag Sensor Assembly | *h | to ECM |
Disconnect the No. 11 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*: w/ Stop and Start System |
|||
| G188-1 (CANH) - G188-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Main body ECU (multiplex network body ECU) |
| G188-2 (CANH) - G188-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| G188-3 (CANH) - G188-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly (skid control ECU) |
| G188-4 (CANH) - G188-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 12 CAN junction connector |
| G188-5 (CANH) - G188-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Engine stop and start ECU* |
| G188-6 (CANH) - G188-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag sensor assembly |
| G188-7 (CANH) - G188-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 12 CAN junction connector CAN main wire) | B |
| NG (ECM CAN main wire) | C |
| NG (ECU or sensor CAN branch wires) | D |
A
B
C
D
Reconnect the G188 No. 11 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 12 CAN junction connector.
| *a | Rear view of wire harness connector
(to No. 12 CAN Junction Connector) |
*b | to Combination Meter Assembly |
| *c | to Power Steering ECU Assembly | *d | to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) |
| *e | to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) | *f | to 4WD ECU Assembly (for 4WD/AWD) |
| *g | to No. 11 CAN Junction Connector | *h | to Central Gateway ECU |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*1: w/ Entry and Start System *2: for 4WD/AWD |
|||
| G189-1 (CANH) - G189-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| G189-2 (CANH) - G189-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU assembly |
| G189-4 (CANH) - G189-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Spiral with sensor cable sub-assembly (steering angle sensor) |
| G189-5 (CANH) - G189-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Certification ECU (smart key ECU assembly)*1 |
| G189-6 (CANH) - G189-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4WD ECU assembly*2 |
| G189-8 (CANH) - G189-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 11 CAN junction connector |
| G189-10 (CANH) - G189-21 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Central gateway ECU |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 11 CAN junction connector CAN main wire) | B |
| NG (Combination meter assembly CAN main wire) | C |
| NG (Central gateway ECU CAN branch wire) | D |
| NG (ECU or sensor CAN branch wires) | E |
A
B
C
D
E
Reconnect the G189 No. 12 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-32 (CANH) - G16-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G189 No. 12 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Central Gateway ECU) |
Disconnect the central gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G170-18 (CA4H) - G170-17 (CA4L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Central Gateway ECU) |
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G170-18 (CA4H) - G170-17 (CA4L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G188 No. 11 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *A | for 2AR-FE, 3ZR-FAE, 3ZR-FE |
| *B | for 2WW |
| *C | for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF |
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-13 (CANH) - A62-26 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-26 (CANH) - A62-25 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A61-7 (CANH) - A61-6 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE: Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
for 2AD-FTV: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FHV: Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
for 2AD-CCo, 2AD-DPF: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2WW: Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL
NG