Home › Drivetrain › K120 (MULTIDRIVE / CVT) › TRANSMISSION CONTROL CABLE › 2018.10–2020.08
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0371725 TRANSMISSION CONTROL CABLE A

K120 MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
C332327

·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 74404B 4.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 53895B 5.REMOVE FRONT FENDER SPLASH SHIELD RH

Hide 53896B 6.REMOVE FRONT FENDER SPLASH SHIELD LH

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51420 8.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 58166A 9.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58810J 10.REMOVE CONSOLE BOX ASSEMBLY

Hide 58861B 11.REMOVE NO. 1 CONSOLE BOX DUCT

Hide 33820B 12.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 33820B 13.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C403003C01
1.75,2.75 2,2.5 2,2.5 2.167,2.5 false 2.208,2.417 2.375,2.583 0.167,0.167 10 false *a 3,3.5 3.167,3.667 0.167,0.167 10 false *b
*a Clip
*b 45° to 60°


While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


b.
C403001

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


c.
C403005

Remove the nut and disconnect the transmission control cable assembly from the vehicle body.


d.
C403007

Remove the 2 nuts and then remove the transmission control cable assembly from the vehicle body.