Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2018.10–2020.08
RM3620E _51 Engine / Hybrid System _076500 M20A-FKS ENGINE MECHANICAL _0372437 REAR CRANKSHAFT OIL SEAL A

M20A-FKS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Vehicle Identification Number (VIN) registration DTC P063051 is output (Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart entry and start system (for Entry Function)

·

smart entry and start system (for Start Function)

·

Steering lock function


for K120, K120F:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for K120:(Click here)
for K120F:(Click here)

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Front exhaust pipe assembly*2 GPF deposition value clear
·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Replacement of continuously variable transaxle assembly
for K120, K120F:
·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for K120:(Click here)
for K120F:(Click here)
Replacement of CVT fluid Air bleed oil pump with motor assembly Stop and start system (Click here)
ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for K120:(Click here)
for K120F:(Click here)
Replacement of front bumper assembly
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Front television camera view adjustment Panoramic view monitor system (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 30300 1.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

Hide 31210 3.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31250 4.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 13405 5.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A426058N02
0.99,0.75 0.99,1.333 0.99,1.333 1.406,1.333 false 0.677,0.75 1.177,0.75 false 0.354,0.677 0.813,0.875 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A431795

Remove the 8 bolts and flywheel sub-assembly.


Hide 32101B 6.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A426058N01
0.99,0.75 0.99,1.333 0.99,1.333 1.406,1.333 false 0.677,0.75 1.177,0.75 false 0.354,0.677 0.813,0.875 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A400433

Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly.


Hide 19315 7.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A426060

Remove the No. 1 crankshaft position sensor plate.


Hide 11401L 8.REMOVE REAR ENGINE OIL SEAL

a.
A426061C01
2.99,1.458 3.177,0.771 true 1.625,1.615 1.354,1.292 true 2.917,1.49 3.229,1.688 0.313,0.198 10 false *b 1.646,1.531 1.865,1.729 0.219,0.198 10 true *a
*a Protective Tape
*b Cut Position


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.


HINT:

Tape the screwdriver tip before use.