Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER (for 4WD/AWD) › 2018.10–2019.02
RM3620E _53 Suspension _076491 REAR SUSPENSION _0373103 REAR SUSPENSION MEMBER(for 4WD/AWD) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for 4WD/AWD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Rear wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for Gasoline model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for A25A-FKS w/ Canister Pump Module:

(Click here)

·

for A25A-FKS w/o Canister Pump Module:

(Click here)

·

for M20A-FKS:

(Click here)



CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 41110 1.REMOVE TORQUE VECTORING DIFFERENTIAL CARRIER ASSEMBLY (for Torque Vectoring Differential)

Hide 41110 2.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY (except Torque Vectoring Differential)

Hide 48740F 3.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 4.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 5.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C410956

Remove the bolt, nut and rear No. 1 suspension arm assembly from the rear suspension member sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48710A 6.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51206A 7.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.

Disengage the 7 clamps to separate the differential carrier wire harness.

C406805


b.
C403462C01
0.583,3.833 0.75,3.833 0.75,3.833 0.833,3.917 false 1.417,3.865 1.583,3.865 1.583,3.865 1.667,3.948 false 1.583,4.344 2.25,4.344 2.25,4.344 2.583,4.094 true 1.917,4.344 2.25,4.094 true 2.896,3.99 2.896,3.74 2.896,3.74 2.979,3.74 false 3.021,3.677 3.271,3.927 0.25,0.25 10 false *a 0.417,3.771 0.667,4.021 0.25,0.25 10 false *b 1.417,4.271 1.75,4.521 0.333,0.25 10 false *b 1.25,3.802 1.667,4.052 0.417,0.25 10 false *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
C410424

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.



c.

Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH.


d.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



e.

Remove the 4 rear suspension member cushions from the rear suspension member sub-assembly.

HINT:

Make sure to place an identification mark on the rear suspension member cushion so that they can be reinstalled to their original positions.



Hide 48790 8.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 9.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 52272A 10.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

Hide 52271E 11.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 52276B 12.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH

Hide 52275C 13.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH

HINT:

Perform the same procedure as for the LH side.


Hide 41651 14.REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

Hide 15.REMOVE HOLE PLUG

a.
C403464N01
0.333,0.042 0.49,0.24 0.156,0.198 10 false A 0.51,0.094 0.667,0.292 0.156,0.198 10 false A 0.646,0.083 0.802,0.281 0.156,0.198 10 false A 0.958,0.052 1.115,0.25 0.156,0.198 10 false B 1.76,0.469 1.917,0.667 0.156,0.198 10 false B 1.542,0 1.698,0.198 0.156,0.198 10 false A 3.135,0.677 3.292,0.875 0.156,0.198 10 false A 2.073,0.792 2.229,0.99 0.156,0.198 10 false A 1.479,0.74 1.604,0.958 0.125,0.219 10 true A 1.125,0.49 1.25,0.708 0.125,0.219 10 true A

Remove the 10 hole plugs from the rear suspension member sub-assembly.

HINT:

There are 2 different shapes of hole plug.