Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER (for 4WD/AWD) › 2018.10–2019.02
RM3620E _52 Drivetrain _076176 AXLE AND DIFFERENTIAL _0371993 REAR AXLE CARRIER(for 4WD/AWD) A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER(for 4WD/AWD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

a.
C405138

Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




b.

Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



c.
C405157N01
0.948,0.323 1.167,0.531 0.219,0.208 10 true A 1.094,1.521 1.313,1.729 0.219,0.208 10 true A 2.01,0.115 2.229,0.323 0.219,0.208 10 true B

Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 3 bolts and nut.

Torque:
Bolt A : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Bolt B : 75 N*m (765 kgf*cm, 55 ft.*lbf)


Hide 48720A 2.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48258C 3.INSTALL REAR LOWER COIL SPRING INSULATOR LH

Hide 48231B 4.INSTALL REAR COIL SPRING LH

Hide 48790 6.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48720A 7.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C407519

Install the rear No. 1 suspension arm assembly with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48740F 8.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48540 9.INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48840A 10.INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 47352B 11.INSTALL NO. 2 FLEXIBLE HOSE BRACKET

a.

Install the flexible hose bracket to the rear axle carrier sub-assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 42450B 12.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 42431 13.INSTALL REAR DISC

Hide 14.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH

a.
C407494

Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


Hide 47319F 15.CONNECT REAR FLEXIBLE HOSE LH

a.
C412369

Connect the rear flexible hose LH to the rear flexible hose bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 89408C 16.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Hide 42312B 17.INSTALL REAR AXLE SHAFT NUT

a.

Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new rear drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.

Using a 30 mm socket wrench, install the rear axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

NOTICE:

Stake the rear axle shaft nut after inspecting for looseness and runout in the following steps.


HINT:

Depress the brake pedal to prevent the drive shaft from rotating.



c.
C407438

Using a chisel and hammer, stake the rear axle shaft nut.


Hide 890C0A 18.INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C405134

Install the No. 2 parking brake wire assembly to the rear trailing arm assembly with the nut.

Torque:
15.5 N*m (158 kgf*cm, 11 ft.*lbf)


b.

Engage the 2 clamps.


c.
C397667

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.


d.
C397676

Connect the rear skid control sensor connector to the rear axle carrier sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 48738C 19.INSTALL LOWER NO. 2 CONTROL ARM COVER (w/ Cover)

Hide 20.INSTALL REAR WHEEL

Hide 48740F 21.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 22.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 24.PERFORM INITIALIZATION

Parking Support Brake System (for Gasoline model) (Click here)
Parking Assist Monitor System (Click here)
Panoramic View Monitor System (for Gasoline model) (Click here)
Lighting System (EXT) (Click here)