Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
42450B
1.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for 2WD)
Install the rear axle hub and bearing assembly and rear disc brake dust cover sub-assembly to the rear axle carrier sub-assembly with the 4 bolts.
42450B
2.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD/AWD)
| *a | Matchmark |
Align the matchmarks on the rear drive shaft assembly and rear axle hub and bearing assembly.
Be careful not to damage the thread portion of the rear drive shaft assembly.
Install the rear axle hub sub-assembly and rear disc brake dust cover to the rear axle carrier with the 4 bolts.
Be careful not to damage the drive shaft boot.
42431
3.INSTALL REAR DISC (for 4WD/AWD)
4.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH (for 4WD/AWD)
42312B
5.TEMPORARILY INSTALL REAR AXLE SHAFT NUT (for 4WD/AWD)
Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using non-residue solvent.
Be sure to perform this work even when using a new rear drive shaft assembly.
Keep the threaded parts free of oil and foreign matter.
Using a 30 mm socket wrench, install the rear axle shaft nut.
Stake the rear axle shaft nut after inspecting for looseness and runout in the following steps.
Depress the brake pedal to prevent the drive shaft from rotating.
6.DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH (for 4WD/AWD)
42431
7.REMOVE REAR DISC (for 4WD/AWD)
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
8.INSPECT REAR AXLE HUB BEARING LOOSENESS
9.INSPECT REAR AXLE HUB RUNOUT
42431
10.INSTALL REAR DISC
11.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH
for 2WD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE CARRIER (for 2WD)>INSTALLATION
for 4WD/AWD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE CARRIER (for 4WD/AWD)>INSTALLATION
47319F
12.CONNECT REAR FLEXIBLE HOSE LH
for 2WD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE CARRIER (for 2WD)>INSTALLATION
for 4WD/AWD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE CARRIER (for 4WD/AWD)>INSTALLATION
13.STAKE REAR AXLE SHAFT NUT (for 4WD/AWD)
Using a chisel and hammer, stake the rear axle shaft nut.
890C0A
14.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for 2WD)
Connect the No. 2 parking brake wire assembly connector to the rear axle hub and bearing assembly.
89544E
15.CONNECT SKID CONTROL SENSOR (for 4WD/AWD)
Connect the skid control sensor to the rear axle carrier sub-assembly with the bolt.
890C0A
16.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.
17.INSTALL REAR WHEEL
18.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/o Vacuum Brake Booster)
Connect the reservoir level switch connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
Perform the following procedure if air bleeding is not necessary:
Turn the power switch on (READY).
Depress the brake pedal and release it.
19.CHECK FOR SPEED SENSOR SIGNAL
w/ Vacuum Brake Booster: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster)>TEST MODE PROCEDURE
w/o Vacuum Brake Booster: Click hereClick hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE