When an incorrect ECM, main body ECU (multiplex network body ECU) or skid control ECU (brake actuator assembly) is installed after the assist map has been written to the power steering ECU (rack and pinion power steering gear assembly), DTC C1582 is stored because the information stored in the power steering ECU (rack and pinion power steering gear assembly) does not match the vehicle specifications.
When an incorrect hybrid vehicle control ECU assembly, main body ECU (multiplex network body ECU) or skid control ECU (brake booster with master cylinder assembly) is installed after the assist map has been written to the power steering ECU (rack and pinion power steering gear assembly), DTC C1582 is stored because the information stored in the power steering ECU (rack and pinion power steering gear assembly) does not match the vehicle specifications.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition | Note |
|---|---|---|---|---|---|---|
| C1582 | Assist Map Number Mismatch | Assist map number mismatch | for Gasoline Model:
·
CAN communication system ·
Incorrect ECM ·
Incorrect main body ECU (multiplex network body ECU) ·
Incorrect skid control ECU (brake actuator assembly) ·
Rack and pinion power steering gear assembly for HV Model:
·
CAN communication system ·
Incorrect hybrid vehicle control ECU assembly ·
Incorrect main body ECU (multiplex network body ECU) ·
Incorrect skid control ECU (brake booster with master cylinder assembly) ·
Rack and pinion power steering gear assembly |
EPS warning light: Does not come on | Ignition switch is turned to ON again | - |
If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
Related parts store information necessary for assist map writing.
Related Part:
ECM
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake actuator assembly)
Hybrid vehicle control ECU assembly
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake booster with master cylinder assembly)
Check for DTCs.
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output. (for Gasoline Model) | A |
| CAN communication system DTCs are not output. (for HV Model) | B |
| CAN communication system DTCs are output. | C |
A
B
C
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the part below has been replaced with an incorrect part in the past.
| Related Part | ECM |
| Main body ECU (multiplex network body ECU) | |
| Skid control ECU (brake actuator assembly) |
When removing the related part to check it, be sure to follow the appropriate procedures and precautions.
ECM
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
Main body ECU (multiplex network body ECU)
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Skid control ECU (brake actuator assembly)
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD with Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD with Vacuum Brake Booster)>REMOVAL
When DTC C1582 is output and parts have not been exchanged, replace the power steering ECU (rack and pinion power steering gear assembly) as it may have an internal malfunction.
If the rack and pinion power steering gear assembly has been replaced, perform assist map writing.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
| Result | Proceed to |
|---|---|
| The related part has an incorrect part number. | A |
| The related part has the correct part number, or a related part and rack and pinion power steering gear assembly have not been replaced. | B |
A
B
Replace the related part with one that has the correct part number.
ECM
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
Main body ECU (multiplex network body ECU)
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Skid control ECU (brake actuator assembly)
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD with Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD with Vacuum Brake Booster)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Check if the part below has been replaced with an incorrect part in the past.
| Related Part | Hybrid vehicle control ECU assembly |
| Main body ECU (multiplex network body ECU) | |
| Skid control ECU (brake booster with master cylinder assembly) |
When removing the related part to check it, be sure to follow the appropriate procedures and precautions.
Hybrid vehicle control ECU assembly
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL
Main body ECU (multiplex network body ECU)
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Skid control ECU (brake booster with master cylinder assembly)
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD without Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD without Vacuum Brake Booster)>REMOVAL
When DTC C1582 is output and parts have not been exchanged, replace the power steering ECU (rack and pinion power steering gear assembly) as it may have an internal malfunction.
If the rack and pinion power steering gear assembly has been replaced, perform assist map writing.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
| Result | Proceed to |
|---|---|
| The related part has an incorrect part number. | A |
| The related part has the correct part number, or a related part and rack and pinion power steering gear assembly have not been replaced. | B |
A
B
Replace the related part with one that has the correct part number.
Hybrid vehicle control ECU assembly
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID VEHICLE CONTROL ECU>REMOVAL
Main body ECU (multiplex network body ECU)
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Skid control ECU (brake booster with master cylinder assembly)
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD without Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD without Vacuum Brake Booster)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B