Home › Engine / Hybrid System › A25A-FXS (FUEL) › FUEL PUMP (w/ Canister Pump Module)
RM3620E _51 Engine / Hybrid System _076684 A25A-FXS FUEL _0375751 FUEL PUMP(w/ Canister Pump Module) A

A25A-FXS FUEL  FUEL PUMP(w/ Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.

Install a new gasket to the fuel tank assembly.


b.

Set the fuel suction with pump and gauge tube assembly to the fuel tank assembly.

NOTICE:
·

Be careful not to bend the arm of the fuel sender gauge assembly.

·

To avoid applying excessive force to the tip of the fuel sender gauge assembly, tilt the fuel sub-tank sub-assembly diagonally and insert it into the fuel tank assembly as shown in the illustration.


A428828C01
1.615,0.688 2.198,0.438 2.198,0.438 2.448,0.438 true 1.385,1.365 2.135,1.031 2.135,1.031 2.385,1.031 true 1.625,1.594 2.271,2.146 2.271,2.146 2.438,2.146 true 5.375,0.979 5.958,0.646 5.958,0.646 6.208,0.646 true 5.656,1.635 6.156,2.219 6.156,2.219 6.406,2.219 true 4.583,2.292 4.833,2.292 4.833,2.292 5.417,1.708 true 2.49,0.354 2.802,0.51 0.313,0.156 10 false *1 2.417,0.948 2.729,1.104 0.313,0.156 10 false *2 2.469,2.063 2.781,2.219 0.313,0.156 10 false *3 4.396,2.198 4.708,2.354 0.313,0.156 10 false *2 6.25,0.563 6.563,0.719 0.313,0.156 10 false *1 6.448,2.135 6.76,2.292 0.313,0.156 10 false *3
*1 Plate Sub-assembly *2 Fuel Sub-tank Sub-assembly
*3 Fuel Sender Gauge Assembly - -




c.
A434636C01
0.677,0.969 0.438,0.792 0.438,0.792 0.292,0.792 true 2.885,0.927 3.073,0.615 3.073,0.615 3.188,0.615 true 2.802,1.438 3.135,1.438 true 0.302,1.5 0.563,1.5 true 0.125,0.698 0.354,0.854 0.229,0.156 10 true *a 0.135,1.406 0.354,1.563 0.219,0.156 10 true *b 3.146,1.344 3.365,1.5 0.219,0.156 10 true *b 3.208,0.51 3.427,0.688 0.219,0.177 10 true *a
*a Protrusion
*b Notch


Align the protrusions of the fuel suction with pump and gauge tube assembly with the notches in the fuel tank assembly.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

i.

While pressing down on the fuel suction with pump and gauge tube assembly, temporarily install the fuel pump gauge retainer.


ii.
A428824C01
1.052,3.01 1.385,3.01 true 2.188,0.385 2.49,0.26 2.49,0.26 2.688,0.26 true 1.854,1.281 2.313,1.615 2.313,1.615 2.51,1.615 true 2,0.875 2.667,0.875 true 2.542,1.51 2.75,1.708 0.208,0.198 10 true *c 1.417,2.917 1.625,3.094 0.208,0.177 10 true *d 2.708,0.167 2.938,0.333 0.229,0.167 10 true *a 2.698,0.792 2.948,0.958 0.25,0.167 10 true *b
*a SST (Plate)
*b SST (Bolt)
*c SST (Claw)
*d Insertion Point


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-14031  (09808-01030, 09808-01090)
09808-01071  

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.
A428829C01
1.073,3.573 1.49,3.573 true 0.917,0.406 1.083,0.406 1.083,0.406 1.781,0.615 true 0.333,3.625 0.667,3.625 true 2.458,1.042 2.292,1.042 2.292,1.042 1.604,1.292 true 2.115,1.719 2.656,1.719 true 2.25,2.219 2.083,2.219 2.083,2.219 1.51,1.844 true 0.688,0.313 0.917,0.49 0.229,0.177 10 true *a 2.5,0.948 2.719,1.135 0.219,0.188 10 true *b 2.677,1.604 2.885,1.792 0.208,0.188 10 true *c 2.271,2.125 2.5,2.281 0.229,0.156 10 true *d 0.177,3.542 0.375,3.698 0.198,0.156 10 true *e 1.521,3.479 1.74,3.677 0.219,0.198 10 true *f
*a SST (Handle)
*b Extension Bar
*c SST (Plate)
*d SST (Bolt)
*e Triangle Mark (Fuel Tank Assembly)
*f Triangle Mark (Fuel Pump Gauge Retainer)


Install SST (handle) and an extension bar to SST (plate).

SST
09808-14031  (09808-01010, 09808-01030, 09808-01090)
09808-01071  


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank assembly to install the fuel suction with pump and gauge tube assembly to the fuel tank assembly.

CAUTION:

When turning SST (handle), take care not to hit the console box assembly with your hands or SST (handle).


NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





b.

Attach the claw and install the No. 1 fuel tube clamp to the fuel pump gauge retainer.


c.

Attach the claw and install the fuel sender gauge wire to the fuel pump gauge retainer.


Hide 77209C 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A434625

Push the fuel tube joint of the fuel tank main tube sub-assembly, and install the tube joint clip.

NOTICE:
A124131C07
0.969,0.76 0.729,0.385 0.729,0.385 0.573,0.385 false 1.656,0.573 1.729,0.198 1.729,0.198 1.896,0.198 false 1.625,1.083 2.094,1.479 2.094,1.479 2.26,1.479 true 1.104,3.24 1.375,3.094 1.375,3.094 1.542,3.094 false 2.438,3.271 2.75,2.813 2.75,2.813 2.917,2.813 true 0.792,3.385 1.021,3.729 1.021,3.729 1.188,3.729 true 2.594,3.396 2.938,3.781 2.938,3.781 3.104,3.781 false 1.01,1.396 0.344,1.396 true 1,1.229 0.583,1.219 0.583,1.219 0.583,1.385 true 0.375,0.292 0.594,0.469 0.219,0.177 10 false *b 1.927,0.094 2.146,0.271 0.219,0.177 10 false *a 2.313,1.406 2.531,1.583 0.219,0.177 10 false *1 0.156,1.302 0.375,1.479 0.219,0.177 10 false *c 1.573,3 1.792,3.177 0.219,0.177 10 false *1 2.948,2.729 3.167,2.906 0.219,0.177 10 false *b 0.719,4.354 0.938,4.531 0.219,0.177 10 false *d 2.375,4.344 2.594,4.521 0.219,0.177 10 false *e 1.198,3.635 1.417,3.813 0.219,0.177 10 false *b 3.135,3.688 3.354,3.865 0.219,0.177 10 false *1
*1 Tube Joint Clip
*a Nylon Tube
*b Fuel Tube Joint
*c O-ring
*d Correct
*e Incorrect


·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 77404 4.CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

a.

Connect the fuel tank vent hose sub-assembly to the fuel suction with pump and gauge tube assembly.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 58325E 6.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Connect the 3 connectors to the fuel suction with pump and gauge tube assembly and fuel gauge wire.


b.

Install the rear floor service hole cover with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Return the floor carpet to its original position.


Hide 58903A 7.INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY

Hide 58464D 8.INSTALL BATTERY SERVICE COVER BOARD

Hide 58466J 9.INSTALL NO. 2 BATTERY SERVICE COVER BOARD

Hide 67917C 10.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 58467H 11.INSTALL NO. 3 BATTERY SERVICE COVER BOARD

Hide 67918E 12.INSTALL REAR DOOR SCUFF PLATE LH

Hide 72693 13.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 14.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 15.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 16.INSTALL BATTERY HOLE COVER

Hide 58416K 17.INSTALL REAR NO. 2 FLOOR BOARD

Hide 58410B 18.INSTALL DECK BOARD ASSEMBLY

Hide 20.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION