Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2018.10–2019.09
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375584 LIGHTING SYSTEM U

LIGHTING (EXT)  LIGHTING SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


E402359C01
3.458,7.698 3.854,8 0.396,0.302 5.458,3.292 5.875,3.531 0.417,0.24 3.167,3.323 3.583,3.563 0.417,0.24 1.125,3.313 1.542,3.552 0.417,0.24 1.833,4.583 2.25,4.823 0.417,0.24 1.01,6.198 1.427,6.438 0.417,0.24 3.615,6.198 4.031,6.438 0.417,0.24 5.333,4.594 5.75,4.833 0.417,0.24 6.25,6.271 6.667,6.51 0.417,0.24 5.26,6.365 5.677,6.604 0.417,0.24 5.26,6.063 5.677,6.302 0.417,0.24 3.615,5.844 4.031,6.083 0.417,0.24 1.594,1.177 1.833,1.177 true 1.135,2.948 0.927,2.948 0.927,2.948 0.927,2.333 true 1.573,0.615 1.573,0.396 1.573,0.396 1.74,0.396 true 1.594,1.51 1.833,1.51 true 1.594,1.823 1.833,1.823 true 0.646,1.042 0.844,1.042 true 3.719,0.948 3.875,1.146 0.156,0.198 10 false A 3.604,7.76 3.76,7.958 0.156,0.198 10 false A 0.844,1.635 1.156,1.833 0.313,0.198 10 false 4F 0.844,2 1.156,2.198 0.313,0.198 10 false 4L 1.885,1.104 2.344,1.302 0.458,0.198 10 false G43 1.885,1.427 2.344,1.625 0.458,0.198 10 false G44 1.906,1.771 2.365,1.969 0.458,0.198 10 false G45 1.229,2.854 1.729,3.083 0.5,0.229 10 false 4K*A 1.229,3.052 1.729,3.281 0.5,0.229 10 false 4M*B 1.792,0.344 2.25,0.542 0.458,0.198 10 false *1 5.813,1.073 6.125,1.271 0.313,0.198 10 false 4D 5.813,1.719 6.125,1.917 0.313,0.198 10 false 4A 1.177,3.354 1.635,3.552 0.458,0.198 10 false G45 3.219,3.375 3.677,3.573 0.458,0.198 10 false G44 5.531,3.333 5.99,3.531 0.458,0.198 10 false G43 1.927,4.625 2.24,4.823 0.313,0.198 10 false 4A 5.469,4.635 5.781,4.833 0.313,0.198 10 false 4D 1.167,6.25 1.479,6.448 0.313,0.198 10 false 4F 3.729,6.229 4.042,6.427 0.313,0.198 10 false 4N 6.375,6.323 6.688,6.521 0.313,0.198 10 false 4L 5.385,6.104 5.646,6.323 0.26,0.219 10 false 4K 5.385,6.406 5.74,6.563 0.354,0.156 10 false 4M 5.771,6.083 6.229,6.281 0.458,0.198 10 false *A 5.76,6.354 6.219,6.552 0.458,0.198 10 false *B 0.229,0.958 0.844,1.156 0.615,0.198 10 false 4H*A 0.229,1.167 0.844,1.365 0.615,0.198 10 false 4N*B 3.719,5.885 4.031,6.083 0.313,0.198 10 false 4H 4.083,5.875 4.542,6.073 0.458,0.198 10 false *A 4.083,6.208 4.542,6.406 0.458,0.198 10 false *B
*A except LHD, Manual Transaxle *B for LHD, Manual Transaxle
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



b.

Connect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-32 (IG) - Body ground None - Body ground Ignition power supply Ignition switch ON 10.5 to 16 V*1
11 to 14 V*2
Ignition switch off Below 1 V
A-31 (BECU) - Body ground None - Body ground Auxiliary battery power supply Ignition switch off 11 to 14 V
A-30 (ACC) - Body ground None - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND1) - Body ground None - Body ground Ground Always Below 1 Ω

*1: for Manual Transaxle with Stop and Start System

*2: except *1




e.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
4A-52 (FFGO) - Body ground*1 G - Body ground FOG FR relay drive output Taillights on, fog light switch in Fr position 11 to 14 V
Taillights on, fog light switch in off position Below 1 V
4F-19 - Body ground*2 LA-BE - Body ground*5
BE - Body ground*6
BKUP LP relay drive output Ignition switch off, shift lever not in R Below 1 V
Ignition switch ON, shift lever in R 11 to 14 V
4F-31 (HRLY) - Body ground R - Body ground H-LP LH relay drive output
·

15 seconds or more after ignition switch turned off

·

Taillights off


11 to 14 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


Below 1 V
4N-10 - Body ground*7 LA-LG - Body ground Back-up lights drive output Ignition switch off, shift lever not in R Below 1 V
Ignition switch ON, shift lever in R 11 to 14 V
4H-10 - Body ground*8 L - Body ground Back-up lights drive output Ignition switch off, shift lever not in R Below 1 V
Ignition switch ON, shift lever in R 11 to 14 V
4N-21 (RFGO) - Body ground*3, *7 R - Body ground Rear fog light drive output Taillights on, fog light switch in Fr&Rr position 11 to 14 V
Taillights on, fog light switch in off position Below 1 V
4H-21 (RFGO) - Body ground*3, *8 LA-R - Body ground Rear fog light drive output Taillights on, fog light switch in Fr&Rr position 11 to 14 V
Taillights on, fog light switch in off position Below 1 V
4N-30 (TRLY) - Body ground*7 LA-W - Body ground Taillights and license plate lights drive output Light control switch in TAIL or HEAD position 11 to 14 V
Light control switch off Below 1 V
4H-30 (TRLY) - Body ground*8 LA-R - Body ground Taillights and license plate lights drive output Light control switch in TAIL or HEAD position 11 to 14 V
Light control switch off Below 1 V
G43-19 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
G45-1 (AHID) - Body ground*4 R - Body ground Auto high beam switch indicator drive output Ignition switch ON, auto high beam switch on Below 1 V
Ignition switch ON, auto high beam switch off 11 to 14 V
G44-12 (HRY2) - Body ground BE - Body ground H-LP RH relay drive output
·

15 seconds or more after ignition switch turned off

·

Taillights off


11 to 14 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


Below 1 V
G44-16 (HEAD) - Body ground LG - Body ground Light control switch HEAD position input Light control switch in HEAD position Below 1 V
Light control switch not in HEAD position 11 to 14 V
G44-23 (CLTB) - G44-25 (CLTE) BE - GR Automatic light control sensor power supply output Ignition switch ON 11 to 14 V
G44-24 (CLTS) - Body ground R - Body ground Automatic light control sensor signal input Ignition switch off Below 1 V
Ignition switch ON Pulse generation
(See waveform 1)
G44-26 (AHBI) - Body ground*4 G - Body ground Auto high beam switch signal input Auto high beam switch on Below 1 V
Auto high beam switch off 11 to 14 V

*1: w/ Front Fog Light

*2: except Manual Transaxle

*3: w/ Rear Fog Light

*4: w/ Automatic High Beam System

*5: for HV Model

*6: for Gasoline Model

*7: for LHD, Manual Transaxle

*8: except LHD, Manual Transaxle


i.
E276298N01
2.844,1.646 3.219,1.813 0.375,0.167 10 false GND

Waveform 1

Item Content
Tester Connection G44-24 (CLTS) - Body ground
Tool setting 2 V/DIV., 10 ms./DIV.
Condition Ignition switch ON

HINT:

The communication waveform changes according to the surrounding brightness.





CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (for Triple Beam Headlight)


E334043E12
2.156,0.156 2.646,0.396 0.49,0.24 5.531,0.271 6.021,0.51 0.49,0.24 2.281,0.198 2.74,0.396 0.458,0.198 10 false A11 5.74,0.313 6.198,0.51 0.458,0.198 10 false B

a.

Disconnect the A11 headlight ECU sub-assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A11-4 (IG) - Body ground B - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A11-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A11-13 (ECUB) - Body ground B - Body ground Battery power supply
·

15 seconds or more after ignition switch turned off

·

Taillights off


Below 1 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


11 to 14 V


c.

Connect the A11 headlight ECU sub-assembly LH connector.

HINT:
·

Since the A11 headlight ECU sub-assembly LH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.

·

Since the B headlight ECU sub-assembly LH connectors are connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A11-11 (TNS) - Body ground LA-LG - Body ground Front turn signal light signal input Ignition switch ON, front turn signal light off Below 1 V
Ignition switch ON, front turn signal light blinking 11 to 14 V ←→ Below 1 V
A11-16 (SBR) - A11-15 (SGR) LG - R Rear height control sensor sub-assembly LH power supply Ignition switch ON 4.75 to 5.25 V
A11-17 (SHRL) - A11-15 (SGR) GR - R Rear height control sensor sub-assembly LH signal input Ignition switch ON, vehicle unloaded, vehicle stopped Approximately 2.5 V
(value decreases as the front of the vehicle is raised)
A11-23 (CANL) - Body ground W - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A11-24 (CANH) - Body ground P - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
B-1 (DRL-) - B-10 (DRL+) - Daytime running lights control signal output Daytime running lights off Below 1 V
Daytime running lights on 11 to 14 V
B-2 (CLL-) - B-19 (CLL+) - Clearance lights control signal output Clearance lights off Below 1 V
Clearance lights on 11 to 14 V
B-4 (LOLED2) - B-3 (LOLED0) - Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 11.3 to 15.8 V
B-7 (ACTBI) - B-17 (ACTGI) - Headlight leveling motor power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
B-8 (ACTSI) - B-17 (ACTGI) - Headlight leveling motor signal output Ignition switch ON, low beam headlights on, vehicle height not changed Below 1 V
Ignition switch ON, low beam headlights on, vehicle height changed and maintained for more than 3 seconds 1 to 14 V
B-9 (TURN+) - B-13 (TURN-) - Front turn signal light signal output Ignition switch ON, front turn signal light off Below 1 V
Ignition switch ON, front turn signal light blinking 11 to 14 V ←→ Below 1 V
B-15 (FANP) - B-3 (LOLED0) - High/Lo switching signal input Low beam headlights off Below 1 V
Low beam headlights on Pulse generation
B-20 (HI SOL+) - B-3 (LOLED0) - High beam headlights drive output High beam headlights off Below 1 V
High beam headlights on 11 to 14 V



CHECK HEADLIGHT ECU SUB-ASSEMBLY LH (for Single Beam Headlight)


E334043E12
2.156,0.156 2.646,0.396 0.49,0.24 5.531,0.271 6.021,0.51 0.49,0.24 2.281,0.198 2.74,0.396 0.458,0.198 10 false A11 5.74,0.313 6.198,0.51 0.458,0.198 10 false B

a.

Disconnect the A11 headlight ECU sub-assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A11-4 (IG) - Body ground B - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A11-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A11-13 (ECUB) - Body ground B - Body ground Battery power supply
·

15 seconds or more after ignition switch turned off

·

Taillights off


Below 1 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


11 to 14 V


c.

Connect the A11 headlight ECU sub-assembly LH connector.

HINT:
·

Since the A11 headlight ECU sub-assembly LH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.

·

Since the B headlight ECU sub-assembly LH connectors are connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A11-11 (TNS) - Body ground LA-LG - Body ground Front turn signal light signal input Ignition switch ON, front turn signal light off Below 1 V
Ignition switch ON, front turn signal light blinking 11 to 14 V ←→ Below 1 V
A11-16 (SBR) - A11-15 (SGR) LG - R Rear height control sensor sub-assembly LH power supply Ignition switch ON 4.75 to 5.25 V
A11-17 (SHRL) - A11-15 (SGR) GR - R Rear height control sensor sub-assembly LH signal input Ignition switch ON, vehicle unloaded, vehicle stopped Approximately 2.5 V
(value decreases as the front of the vehicle is raised)
A11-23 (CANL) - Body ground W - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A11-24 (CANH) - Body ground P - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
B-4 (LOLED2) - B-3 (LOLED0) - Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 10.8 to 14.8 V
B-6 (FANB) - B-14 (FANG) - Headlight fan power source Low beam headlights off Below 1 V
Low beam headlights on 4.5 to 5.5 V
B-7 (ACTBI) - B-17 (ACTGI) - Headlight leveling motor power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
B-8 (ACTSI) - B-17 (ACTGI) - Headlight leveling motor signal output Ignition switch ON, low beam headlights on, vehicle height not changed Below 1 V
Ignition switch ON, low beam headlights on, vehicle height changed and maintained for more than 3 seconds 1 to 14 V
B-9 (TURN+) - B-13 (TURN-) - Front turn signal light signal output Ignition switch ON, front turn signal light off Below 1 V
Ignition switch ON, front turn signal light blinking 11 to 14 V ←→ Below 1 V
B-10 (DRL/CLL+) - B-1 (DRL/CLL-) - Clearance lights/daytime running lights power source Clearance lights and daytime running lights off Below 1 V
Clearance lights and daytime running lights on 11 to 14 V
B-15 (FANP) - B-14 (FANG) - Headlight fan control signal input Low beam headlights off Below 1 V
Low beam headlights on Pulse generation
B-19 (CLL+) - B-1 (DRL/CLL-) - Clearance lights/daytime running lights control signal output Clearance lights and daytime running lights off Below 1 V
Clearance lights and daytime running lights on Pulse generation
B-20 (HI SOL+) - B-11 (HI SOL-) - High beam headlights drive output High beam headlights off Below 1 V
High beam headlights on 11 to 14 V



CHECK HEADLIGHT ECU SUB-ASSEMBLY RH (for Triple Beam Headlight)


E334043E22
2.156,0.156 2.646,0.396 0.49,0.24 5.531,0.271 6.021,0.51 0.49,0.24 2.281,0.198 2.74,0.396 0.458,0.198 10 false A12 5.74,0.313 6.198,0.51 0.458,0.198 10 false B

a.

Disconnect the A12 headlight ECU sub-assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A12-4 (IG) - Body ground B - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A12-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A12-13 (ECUB) - Body ground BE - Body ground Battery power supply
·

15 seconds or more after ignition switch turned off

·

Taillights off


Below 1 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


11 to 14 V


c.

Connect the A12 headlight ECU sub-assembly RH connector.

HINT:
·

Since the A12 headlight ECU sub-assembly RH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.

·

Since the B headlight ECU sub-assembly RH connectors are connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A12-11 (TNS) - Body ground LA-G - Body ground Front turn signal light signal input Ignition switch ON, front turn signal light off Below 1 V
Ignition switch ON, front turn signal light blinking 11 to 14 V ←→ Below 1 V
A12-23 (CANL) - Body ground W - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A12-24 (CANH) - Body ground L - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
B-1 (DRL-) - B-10 (DRL+) - Daytime running lights control signal output Daytime running lights off Below 1 V
Daytime running lights on 11 to 14 V
B-2 (CLL-) - B-19 (CLL+) - Clearance lights control signal output Clearance lights off Below 1 V
Clearance lights on 11 to 14 V
B-4 (LOLED2) - B-3 (LOLED0) - Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 11.3 to 15.8 V
B-7 (ACTBI) - B-17 (ACTGI) - Headlight leveling motor power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
B-8 (ACTSI) - B-17 (ACTGI) - Headlight leveling motor signal output Ignition switch ON, low beam headlights on, vehicle height not changed Below 1 V
Ignition switch ON, low beam headlights on, vehicle height changed and maintained for more than 3 seconds 1 to 14 V
B-9 (TURN+) - B-13 (TURN-) - Front turn signal light signal output Ignition switch ON, front turn signal light off Below 1 V
Ignition switch ON, front turn signal light blinking 11 to 14 V ←→ Below 1 V
B-15 (FANP) - B-3 (LOLED0) - High/Lo switching signal input Low beam headlights off Below 1 V
Low beam headlights on Pulse generation
B-20 (HI SOL+) - B-3 (LOLED0) - High beam headlights drive output High beam headlights off Below 1 V
High beam headlights on 11 to 14 V



CHECK HEADLIGHT ECU SUB-ASSEMBLY RH (for Single Beam Headlight)


E334043E22
2.156,0.156 2.646,0.396 0.49,0.24 5.531,0.271 6.021,0.51 0.49,0.24 2.281,0.198 2.74,0.396 0.458,0.198 10 false A12 5.74,0.313 6.198,0.51 0.458,0.198 10 false B

a.

Disconnect the A12 headlight ECU sub-assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A12-4 (IG) - Body ground B - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A12-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A12-13 (ECUB) - Body ground BE - Body ground Battery power supply
·

15 seconds or more after ignition switch turned off

·

Taillights off


Below 1 V
·

Ignition switch ON or within 15 seconds after ignition switch turned off

·

Taillights on


11 to 14 V


c.

Connect the A12 headlight ECU sub-assembly RH connector.

HINT:
·

Since the A12 headlight ECU sub-assembly RH connector is a waterproof type connector, the voltage and pulses cannot be checked directly. The values listed are for reference only.

·

Since the B headlight ECU sub-assembly RH connectors are connected inside the headlight assembly, the voltage and pulses cannot be checked directly. The values listed are for reference only.




d.

Measure the voltage and check of pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A12-11 (TNS) - Body ground LA-G - Body ground Front turn signal light signal input Ignition switch ON, front turn signal light off Below 1 V
Ignition switch ON, front turn signal light blinking 11 to 14 V ←→ Below 1 V
A12-23 (CANL) - Body ground W - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
A12-24 (CANH) - Body ground L - Body ground CAN communication line Ignition switch off Below 1 V
Ignition switch ON Pulse generation
B-4 (LOLED2) - B-3 (LOLED1) - Low beam headlights drive output Low beam headlights off Below 1 V
Low beam headlights on 10.8 to 14.8 V
B-6 (FANB) - B-14 (FANG) - Headlight fan power source Low beam headlights off Below 1 V
Low beam headlights on 4.5 to 5.5 V
B-7 (ACTBI) - B-17 (ACTGI) - Headlight leveling motor power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
B-8 (ACTSI) - B-17 (ACTGI) - Headlight leveling motor signal output Ignition switch ON, low beam headlights on, vehicle height not changed Below 1 V
Ignition switch ON, low beam headlights on, vehicle height changed and maintained for more than 3 seconds 1 to 14 V
B-9 (TURN+) - B-13 (TURN-) - Front turn signal light signal output Ignition switch ON, front turn signal light off Below 1 V
Ignition switch ON, front turn signal light blinking 11 to 14 V ←→ Below 1 V
B-10 (DRL/CLL+) - B-1 (DRL/CLL-) - Clearance lights/daytime running lights power source Clearance lights and daytime running lights off Below 1 V
Clearance lights and daytime running lights on 11 to 14 V
B-15 (FANP) - B-14 (FANG) - Headlight fan control signal input Low beam headlights off Below 1 V
Low beam headlights on Pulse generation
B-19 (CLL+) - B-1 (DRL/CLL-) - Clearance lights/daytime running lights control signal output Clearance lights and daytime running lights off Below 1 V
Clearance lights and daytime running lights on Pulse generation
B-20 (HI SOL+) - B-11 (HI SOL-) - High beam headlights drive output High beam headlights off Below 1 V
High beam headlights on 11 to 14 V




CHECK FORWARD RECOGNITION CAMERA (w/ Automatic High Beam System)


Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>TERMINALS OF ECU