Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING › 2018.10–2019.02
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377756 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door window frame moulding are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV Model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV Model) (Click here)
Reset back door close position Power back door system (for HV Model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline Model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline Model) (Click here)
Reset back door close position Power back door system (for Gasoline Model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.

·

When performing removal for the rear door window frame moulding, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL



c.

for M20A-FKS:

Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 69278C 6.REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

Hide 74646A 7.REMOVE DOOR ASSIST GRIP COVER LH

Hide 8.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 67604 9.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 68174A 10.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

Hide 68199 11.REMOVE REAR DOOR REAR BELT SEAL LH

Hide 67842E 12.REMOVE REAR DOOR SERVICE HOLE COVER LH

Hide 67674A 13.REMOVE REAR DOOR FRAME GARNISH LH

Hide 68152C 14.DISCONNECT REAR DOOR GLASS RUN LH

Hide 67408E 15.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68124C 16.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

Hide 68104 17.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 75722A 18.REMOVE REAR DOOR BELT MOULDING LH

Hide 67872 19.REMOVE REAR DOOR WEATHERSTRIP LH

a.
B524170C01
0,0 0,0 false
V100155

Protective Tape


Using a clip remover with its tip wrapped with protective tape, detach the clip and remove the clip.


b.
B524171

Using a screwdriver with its tip wrapped with protective tape, detach the clip and remove part of the rear door weatherstrip LH.


Hide 75762B 20.REMOVE REAR DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)

HINT:

When removing the rear door window frame moulding LH (center pillar side), if the double-sided tape is difficult to remove, heat the adhesive of the rear door window frame moulding LH (center pillar side) and rear door panel using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Rear Door Window Frame Moulding LH (Center Pillar Side) 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear door panel and rear door window frame moulding LH (center pillar side) excessively.


a.

Using a heat light, heat the rear door panel and rear door window frame moulding LH (center pillar side).


b.
B524088C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear door window frame moulding LH (center pillar side) as shown in the illustration.


c.
B524089

Using moulding remover D, detach the clip.


d.
B524189C01
0.792,1.438 1.563,1.438 true 0.542,1.333 0.729,1.521 0.188,0.188 10 true *a
*a Double-sided Tape


Using a scraper, start from the top and remove the double-sided tape from the back of the rear door window frame moulding LH (center pillar side).


e.
B524090C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Detach the guide and remove the rear door window frame moulding LH (center pillar side).


Hide 67846A 21.REMOVE REAR DOOR FRONT OUTSIDE SEAL LH

a.
B524091C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door front outside seal LH.


Hide 75766B 22.REMOVE REAR DOOR WINDOW FRAME MOULDING LH (REAR PILLAR SIDE)

a.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


b.
B360296C07
0.542,0.906 0.833,1.219 false 0.875,1.156 1.188,1.313 0.313,0.156 10 false *a 0.333,1.5 0.49,1.698 0.156,0.198 10 false A
*a Tape


Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.
B524092C02
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear door window frame moulding LH (rear pillar side) as shown in the illustration.


d.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 3 rivets.

B524093

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




e.

Detach the guide to remove the rear door window frame moulding LH (rear pillar side) from the rear door frame.


f.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.


Hide 75764A 23.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING LH

a.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


b.
B360296C07
0.542,0.906 0.833,1.219 false 0.875,1.156 1.188,1.313 0.313,0.156 10 false *a 0.333,1.5 0.49,1.698 0.156,0.198 10 false A
*a Tape


Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.
B524094C02
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear door upper window frame moulding LH as shown in the illustration.


d.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 4 rivets.

B524095

CAUTION:

Be careful of the drilled rivets, as they may be hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.




e.

Detach the guide to remove the rear door upper window frame moulding LH from the rear door frame.


f.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.