Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2018.10–2019.02
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0377463 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door disassembly/reassembly are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Power window regulator motor assembly LH

·

Power window regulator motor assembly RH

·

Rear door window regulator sub-assembly LH

·

Rear door window regulator sub-assembly RH

·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Power window regulator motor assembly LH

·

Power window regulator motor assembly RH

·

Rear door window regulator assembly LH

·

Rear door window regulator assembly RH

·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH

·

Rear door No. 3 glass run LH

·

Rear door No. 3 glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.

·

When performing disassembly for the rear door, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL



c.

for M20A-FKS:

Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>REMOVAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 69278C 6.REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

a.
B522612

Detach the claw and remove the rear door inside handle bezel LH.


Hide 74646A 7.REMOVE DOOR ASSIST GRIP COVER LH

a.
B522613C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the rear door trim board sub-assembly LH as shown in the illustration.


b.
B522614C01
1.792,1.115 1.938,1.292 0.146,0.177 10 true 1 1.844,1.896 1.99,2.073 0.146,0.177 10 true 1 2.115,1.052 2.26,1.229 0.146,0.177 10 true 1 2.75,1.313 2.896,1.49 0.146,0.177 10 true 1 2.927,0.979 3.073,1.156 0.146,0.177 10 true 2 2.313,0.75 2.458,0.927 0.146,0.177 10 true 2 3.063,0.313 3.208,0.49 0.146,0.177 10 true 3 1.375,1.229 1.521,1.406 0.146,0.177 10 true 2 1.563,1.885 1.708,2.063 0.146,0.177 10 true 2 1.021,2.042 1.167,2.219 0.146,0.177 10 true 3 0.927,1.365 1.073,1.542 0.146,0.177 10 true 3
V113147

Remove in this Direction


Using a moulding remover A, detach the clip.


c.

Detach the claw in the order shown in the illustration.


d.
B522615C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide in the direction indicated by the arrow shown in the illustration and remove the door assist grip cover LH.


Hide 8.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.
B522616C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear power window regulator switch assembly with rear door armrest base panel.


b.
B522617C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover A, detach the guide and claw as shown in the illustration.


c.
B522618C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide in the direction indicated by the arrow shown in the illustration and remove the rear power window regulator switch assembly with rear door armrest base panel.


d.

w/ Seat Heater Switch:

i.

Disconnect the 2 connectors.



e.

w/o Seat Heater Switch:

i.

Disconnect the connector.



Hide 84751R 9.REMOVE REAR SEAT HEATER SWITCH (w/ Seat Heater System)

Hide 84810D 10.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 67604 11.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B522619C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the rear door panel as shown in the illustration.


b.
B522620

Remove the 3 screws.


c.
B522621C01
2.813,3 2.969,3.198 0.156,0.198 10 true 1 2.302,3.208 2.458,3.406 0.156,0.198 10 true 2 1.635,3.146 1.792,3.344 0.156,0.198 10 true 3 0.906,2.198 1.063,2.396 0.156,0.198 10 true 5 1.25,2.656 1.406,2.854 0.156,0.198 10 true 4 2.833,2.208 2.99,2.406 0.156,0.198 10 true 5
V113146

Place Hand Here
V113147

Remove in this Direction


Place your hand at the position shown in the illustration, and while pulling the rear door trim board sub-assembly LH toward you, detach the clip and disconnect the rear door trim board sub-assembly LH from the rear door panel.

HINT:
·

Detach the clip in the order shown in the illustration.

·

Securely detach the clip one by one.




d.
B522622C01
0.656,1.125 0.813,1.323 0.156,0.198 10 true 1 1.177,1.156 1.333,1.354 0.156,0.198 10 true 2 1.531,1.146 1.688,1.344 0.156,0.198 10 true 3 1.917,1.125 2.073,1.323 0.156,0.198 10 true 4 2.281,1.125 2.438,1.323 0.156,0.198 10 true 5 2.656,1.083 2.813,1.281 0.156,0.198 10 true 6 0.281,1.458 0.438,1.656 0.156,0.198 10 true 7 2.875,1.677 3.031,1.875 0.156,0.198 10 true 8
V113147

Remove in this Direction


Pull the rear door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration to detach the claw and clip to remove the rear door trim board sub-assembly LH.

HINT:

Detach the claw and clip in the order shown in the illustration.



e.
B522623C01
1.938,0.823 2.313,0.417 true 1.125,1.656 1.938,1.323 true 0.854,1.615 1.073,1.813 0.219,0.198 10 true *2 2.365,0.26 2.583,0.458 0.219,0.198 10 true *1
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Detach the clamp and disconnect the rear door inside locking cable assembly and rear door lock remote control cable assembly in the direction indicated by the arrow shown in the illustration.


Hide 69206C 12.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B522624

Detach the clamp and claw.


b.
B522625C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door inside handle sub-assembly LH in the direction indicated by the arrow as shown in the illustration.


Hide 68174A 13.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B522626C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a clip remover with its tip wrapped with protective tape, detach the clip.


b.

Detach the guide and pull back the rear door weatherstrip LH so that the rear door inner glass weatherstrip LH can be removed.


c.
B522627C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door inner glass weatherstrip LH with rear door front belt seal LH as shown in the illustration.


Hide 68197A 14.REMOVE REAR DOOR FRONT BELT SEAL LH

a.
B522628C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door front belt seal LH from the rear door inner glass weatherstrip LH as shown in the illustration.


Hide 68199 15.REMOVE REAR DOOR REAR BELT SEAL LH

a.
B522629C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a clip remover with its tip wrapped with protective tape, detach the clip.


b.

Detach the guide and pull back the rear door weatherstrip LH so that the rear door rear belt seal LH can be removed.


c.
B522630C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door rear belt seal LH as shown in the illustration.


Hide 86160B 16.REMOVE REAR SPEAKER ASSEMBLY

Hide 67842E 17.REMOVE REAR DOOR SERVICE HOLE COVER LH

a.
B522631

Disconnect the connector and detach the clamp.


b.
B522632C01
2.323,0.906 2.646,0.635 true 1.875,1.25 2.177,1.063 true 2.688,0.51 2.917,0.729 0.229,0.219 10 true *1 1.604,1.177 1.833,1.396 0.229,0.219 10 true *2
*1 Rear Door Lock Remote Control Cable Assembly
*2 Rear Door Inside Locking Cable Assembly
V113147

Remove in this Direction


Pull out the rear door lock remote control cable assembly and rear door inside locking cable assembly from the rear door service hole cover LH, and then remove the rear door service hole cover LH.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 67674A 18.REMOVE REAR DOOR FRAME GARNISH LH

a.
B522660C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Detach the guide and remove the rear door frame garnish LH in the direction indicated by the arrows, in the order shown in the illustration.


Hide 68152C 19.DISCONNECT REAR DOOR GLASS RUN LH

a.
B522633C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disconnect the rear door glass run LH as shown in the illustration.

HINT:

Leave the rear side of the rear door glass run LH on the rear door window division bar sub-assembly LH.



Hide 67408E 20.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

a.
B522634C01
0,0 0,0 false
V113147

Pull back in this Direction


Pull back part of the rear door weatherstrip LH and remove the screw as shown in the illustration.


b.
B522635C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 bolts and the rear door window division bar sub-assembly LH with rear door glass run LH in the direction of the arrow indicated in the illustration.


Hide 68152C 21.REMOVE REAR DOOR GLASS RUN LH

a.
B536492C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door glass run LH from the rear door window division bar sub-assembly LH.


Hide 68124C 22.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

a.
B522636C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door quarter window glass LH with rear door quarter window weatherstrip LH as shown in the illustration.


Hide 68189 23.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.
B522637

Remove the rear door quarter window weatherstrip LH from the rear door quarter window glass LH.


Hide 68104 24.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

a.
B522638

Remove the hole plug.


b.

Connect the power window regulator switch assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal.





d.

Turn the ignition switch to ON.


e.
B522639

Move the rear door glass sub-assembly LH until the installation bolts can be seen.


f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

iii.


h.

Disconnect the power window regulator switch assembly connector.


i.
B522640

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the rear door glass sub-assembly to fall.



j.
B522641C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door glass sub-assembly LH as shown in the illustration.

NOTICE:

Be careful not to damage the rear door glass sub-assembly LH.



Hide 69804 25.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B522642C02
0,0 0,0 false
V100135

Nut
V100136

Connector


Disconnect the connector.


b.

Remove the 6 nuts and the rear door window regulator sub-assembly LH.

NOTICE:

Do not damage the rear door panel with the rear door window regulator sub-assembly LH.


HINT:
B522643C01
0,0 0,0 false
V113147

Remove in this Direction


When removing the rear door window regulator sub-assembly LH, pull it out from the service hole as shown in the illustration.



Hide 85720D 26.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69060A 27.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

Hide 69318D 28.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)

a.

When reusing rear door lock with motor assembly LH:

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>REMOVAL


Hide 69038A 29.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

Hide 69740E 30.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

Hide 69780E 31.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

Hide 69060A 32.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

Hide 69318D 33.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)

a.

When reusing rear door lock with motor assembly LH:

Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK>REMOVAL


Hide 69740E 34.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

Hide 69780E 35.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

Hide 69240 36.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B522652C01
1.938,1.51 1.938,1.917 1.938,1.917 1.698,1.917 true 1.417,1.833 1.677,2.031 0.26,0.198 10 true *1
*1 Holder
V113147

Remove in this Direction


Detach the holder as shown in the illustration.


b.
B522653C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.


Hide 69227L 37.REMOVE REAR DOOR OUTSIDE HANDLE COVER LH

a.
B522654

Using a T30 "TORX" socket wrench, loosen the "TORX" screw.


b.
B522655C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the rear door outside handle cover LH as shown in the illustration.


Hide 69241G 38.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B522656

Detach the claw and guide to remove the rear door front outside handle pad.


Hide 69242G 39.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B522657

Detach the guide and remove the rear door rear outside handle pad.


Hide 69204A 40.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B522658C01
0.25,0.073 0.521,0.302 0.271,0.229 10 true *a 0.25,2.333 0.521,2.563 0.271,0.229 10 true *b
*a Inside
*b Outside


Using a T30 "TORX" socket wrench, loosen the "TORX"screw.


b.

Detach the guide and remove the rear door outside handle frame sub-assembly LH.


Hide 68640A 41.REMOVE REAR DOOR CHECK ASSEMBLY LH

a.
B522659C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B


Remove the 2 bolts (A), bolt (B) and rear door check assembly LH.


Hide 67872 42.REMOVE REAR DOOR WEATHERSTRIP LH

a.
B522661C01
0,0 0,0 false
V100155

Protective Tape


Using a clip remover with its tip wrapped with protective tape, detach the clip and remove the clip.


b.
B522662C01
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, detach the clip and remove the rear door weatherstrip LH.


Hide 75722A 43.REMOVE REAR DOOR BELT MOULDING LH

Hide 75762B 44.REMOVE REAR DOOR WINDOW FRAME MOULDING LH (CENTER PILLAR SIDE)

Hide 75792 45.REMOVE DOOR WINDOW FRAME MOULDING CLIP

HINT:

Perform the following procedure only when replacement of a door window frame moulding clip in necessary.


a.
B524161

Detach the claw and remove the door window frame moulding clip.


Hide 67846A 46.REMOVE REAR DOOR FRONT OUTSIDE SEAL LH

Hide 75766B 47.REMOVE REAR DOOR WINDOW FRAME MOULDING LH (REAR PILLAR SIDE)

Hide 75764A 48.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING LH

Hide 67874C 49.REMOVE REAR DOOR NO. 5 WEATHERSTRIP LH

a.
B522663

Using a screwdriver with its tip wrapped with protective tape, detach the clip and remove the rear door No. 5 weatherstrip LH.


Hide 75078 50.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 75062 51.REMOVE OUTSIDE MOULDING SET LH (for Off Road Package)

Hide 75062 52.REMOVE OUTSIDE MOULDING SET LH (except Off Road Package)

Hide 67858B 53.REMOVE REAR DOOR PANEL PROTECTOR LH

Hide 67836H 54.REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH

a.
B522664

Remove the rear door lock child protection cover LH.


Hide 55.REMOVE SCREW GROMMET

a.
B522666

Detach the claw and remove the screw grommet.

HINT:

Use the same procedure described for the other side.



Hide 67003C 56.REMOVE REAR DOOR PANEL CUSHION

a.
B522667

Detach the claw and remove the rear door panel cushion.


Hide 57.REMOVE HOLE PLUG

a.
B522668

Remove the hole plug.

HINT:

Use the same procedure described for the other side.



Hide 75978H 58.REMOVE REAR DOOR LOWER OUTSIDE STRIPE LH (w/ Black Out Tape)

Hide 75988E 59.REMOVE REAR DOOR OUTSIDE STRIPE LH (w/ Black Out Tape)

Hide 75954A 60.REMOVE REAR INNER BLACK OUT TAPE LH (w/ Black Out Tape)