Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1203  ECM Communication Circuit  


DESCRIPTION

This circuit is used to send TRC (TRAC) and VSC information from the skid control ECU (brake booster with master cylinder assembly) to the hybrid vehicle control ECU assembly, and hybrid control system information from the hybrid vehicle control ECU assembly to the skid control ECU (brake booster with master cylinder assembly) via CAN communication.

Identification information sent from other ECUs is stored when the vehicle is shipped from the factory and used as the default values.

NOTICE:

DTC C1203 is output when an incorrect ECU is installed. If initialization is performed and learning occurs with an incorrect ECU installed, operations and functions will differ from those stored when the vehicle was shipped from the factory. Therefore, make sure that learning occurs properly.


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1203 ECM Communication Circuit - Either of the following is detected:
1.

Identification information sent from other ECUs does not match with the value stored when shipped from the factory.

2.

No stored information for destination.


·

The wrong ECU or sensor was installed

·

Skid control ECU (Brake booster with master cylinder assembly)


-

DTC Detection Conditions: C1203
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status Identification information sent from other ECUs does not match with the value stored when shipped from the factory ○ -
No stored information for destination - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK PART NUMBER
a.

Check that the proper hybrid vehicle control ECU assembly, main body ECU (multiplex network body ECU) and yaw rate and acceleration sensor (airbag sensor assembly) are installed.

OK:

Proper ECUs and sensor are installed.



b.

Check if the hybrid vehicle control ECU assembly, main body ECU (multiplex network body ECU) and yaw rate and acceleration sensor (airbag sensor assembly) were replaced before the DTC was recorded.

OK:

ECU or sensor was not replaced.



Result:
Result Proceed to
OK A
NG (A proper hybrid vehicle control ECU assembly is not installed and/or the hybrid vehicle control ECU assembly was replaced.) B
NG (A proper main body ECU (multiplex network body ECU) is not installed and/or the main body ECU (multiplex network body ECU) was replaced.) C
NG (A proper yaw rate and acceleration sensor (airbag sensor assembly) is not installed and/or the yaw rate and acceleration sensor (airbag sensor assembly) was replaced.) D



A

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

C

D

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
a.

Perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 1167
HINT:

Before performing initialization and calibration of the linear solenoid valve, DTC C1203 will be output.



Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Turn the power switch off.



c.

Turn the power switch off.


d.

Turn the power switch on (IG).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1203 is output. A
DTC C1203 is not output. B



A

B

END