If the wireless door lock operations cannot be performed, the door control receiver may be malfunctioning, or there may be wave interference or problems in the communication which is used for the wireless function between the door control receiver and certification ECU (smart key ECU assembly).
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to the Service Bulletin.
After repair, confirm that no DTCs are output.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.
for 12 Pin Type:
It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced.
for initialization:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
for registration:
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION
Measure the battery voltage.
11 to 14 V
It may be possible to tell whether the battery is discharged by operating the horn.
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.
Connect the GTS to the DLC3.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
When the doors are locked by operating the wireless door lock function with all doors closed, check that the door ajar warning operates.
Be sure to check the following before performing the procedure.
The engine switch is off.
All the doors are closed.
The lock switch is pressed on the electrical key transmitter sub-assembly.
The electrical key transmitter sub-assembly is in the vehicle exterior detection area.
| Result | Proceed to |
|---|---|
| The buzzer does not sound | A |
| The buzzer sounds | B |
A
B
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
| Result | Proceed to |
|---|---|
| Power door lock function operates normally | A |
| Power door lock function does not operate normally | B |
A
B
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless operation 2 or more times*.
*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| Wireless function does not operate normally | A |
| Wireless function operates normally | B |
A
B
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.
Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the engine switch, depressing the brake pedal*1 or clutch pedal*2 and pressing the engine switch.
*1: except Manual Transaxle
*2: for Manual Transaxle
| Result | Proceed to |
|---|---|
| LED illuminates 3 times or more when switch is pressed and held | A |
| LED does not illuminate when switch is pressed and held | B |
| LED illuminates once or twice but not a third time | C |
A
B
C
Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.
| Result | Proceed to |
|---|---|
| Another registered electrical key transmitter sub-assembly is not available | A |
| Another registered electrical key transmitter sub-assembly is available | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using another registered electrical key transmitter sub-assembly, check that the function operates normally.
| Result | Proceed to |
|---|---|
| Wireless door lock function does not operate normally | A |
| Wireless door lock function operates normally | B |
A
B
Perform registration of the B code.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
After completing B code registration, check that the entry lock and unlock functions can be operated 2 times consecutively.
| Result | Proceed to |
|---|---|
| Wireless door lock function does not operate normally | A |
| Wireless door lock function operates normally | B |
A
B
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| B Code | B code registration status | No Regd or Regd | No Regd: B code not registered correctly
Regd: B code registered correctly |
- |
| Tester Display |
|---|
| B Code |
| Result | Proceed to |
|---|---|
| "No Regd" is displayed on the GTS | A |
| "Regd" is displayed on the GTS | B |
A
B
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| B Code Difference | B code mismatch | No or Yes | No: Communication normal
Yes: Communication malfunction |
- |
| Tester Display |
|---|
| B Code Difference |
| Result | Proceed to |
|---|---|
| "No" is displayed on the GTS | A |
| "Yes" is displayed on the GTS | B |
A
B
Measure the voltage while checking the Data List on the GTS.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | All OFF, ACC ON, IG ON or ST ON | All OFF: Engine switch off
ACC ON: Engine switch on (ACC) IG ON: Engine switch on (IG) ST ON: Sending engine start request signal |
- |
| Tester Display |
|---|
| Power Supply Condition |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G54-17 (IG1D) - Body ground | Engine switch off | Below 1 V |
| Engine switch on (ACC) | Below 1 V | |
| Engine switch on (IG) | 9 V or higher | |
| G54-16 (ACCD) - Body ground | Engine switch off | Below 1 V |
| Engine switch on (ACC) | 8.5 V or higher | |
| Engine switch on (IG) | 8.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ACC SW | Engine switch status | OFF or ON | OFF: Engine switch off
ON: Engine switch on (ACC) |
"ON" is also displayed when the engine switch is on (IG). |
| IG SW | Engine switch status | OFF or ON | OFF: Engine switch off
ON: Engine switch on (IG) |
"OFF" is also displayed when the engine switch is on (ACC). |
| Tester Display |
|---|
| ACC SW |
| IG SW |
If the main body ECU (multiplex network body ECU) misjudges for any reason that the engine switch is on (IG) even though the engine switch is off, the wireless lock and unlock functions will be disabled.
| Result | Proceed to |
|---|---|
| The main body ECU (multiplex network body ECU) judges properly that the power source is off when the engine switch is off | A |
| The main body ECU (multiplex network body ECU) does not judge properly that the power source is off when the engine switch is off | B |
A
B
Disconnect the M7 certification ECU (smart key ECU assembly) connector.
Disconnect the M8*1 or M11*2 door control receiver connector.
*1: for 12 Pin Type
*2: for 5 Pin Type
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-18 (RCO) - M8-8 (+5) | Always | Below 1 Ω |
| M7-19 (RDAM) - M8-2 (DATA) | Always | Below 1 Ω |
| M7-20 (CSEL) - M8-6 (CSEL) | Always | Below 1 Ω |
| M8-12 (GND) - Body ground | Always | Below 1 Ω |
| M7-18 (RCO) or M8-8 (+5) - Other terminals and body ground | Always | 10 kΩ or higher |
| M7-19 (RDAM) or M8-2 (DATA) - Other terminals and body ground | Always | 10 kΩ or higher |
| M7-20 (CSEL) or M8-6 (CSEL) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M7-18 (RCO) - M11-4 (+5) | Always | Below 1 Ω |
| M7-19 (RDAM) - M11-5 (DATA) | Always | Below 1 Ω |
| M7-20 (CSEL) - M11-2 (CSEL) | Always | Below 1 Ω |
| M11-1 (GND) - Body ground | Always | Below 1 Ω |
| M7-18 (RCO) or M11-4 (+5) - Other terminals and body ground | Always | 10 kΩ or higher |
| M7-19 (RDAM) or M11-5 (DATA) - Other terminals and body ground | Always | 10 kΩ or higher |
| M7-20 (CSEL) or M11-2 (CSEL) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect all connectors and check that the function operates normally.
| Result | Proceed to |
|---|---|
| Wireless door lock function does not operate normally | A |
| Wireless door lock function operates normally | B |
A
B
| *A | for 5 Pin Type |
| *B | for 12 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M11-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M8-12 (GND) - Body ground | Always | Below 1 Ω |
Using an oscilloscope, check the waveform.
| *A | for 12 Pin Type | *B | for 5 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| *c | Before lock or unlock switch of electrical key transmitter sub-assembly pressed | *d | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M8-2 (DATA) - M8-12 (GND) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms/DIV. | Below 1 V → Pulse generation
(See waveform 1) |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M11-5 (DATA) - M11-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 5.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms/DIV. | Below 1 V → Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for 5 Pin Type |
| *B | for 12 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M11-2 (CSEL) - M11-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors closed |
Below 1 V → Pulse generation |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M8-1 (IG) - M8-12 (GND) | Engine switch on (IG) | 10 to 16 V |
| M8-6 (CSEL) - M8-12 (GND) | Procedure:
1.
Engine switch off 2.
All doors closed |
Below 1 V → Pulse generation |
Using an oscilloscope, check the waveform.
| *A | for 12 Pin Type | *B | for 5 Pin Type |
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| *c | Before lock or unlock switch of electrical key transmitter sub-assembly pressed | *d | After lock or unlock switch of electrical key transmitter sub-assembly pressed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M8-8 (+5) - M8-12 (GND) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| M11-4 (+5) - M11-1(GND) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area 3.
Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the function operates normally.
| Result | Proceed to |
|---|---|
| Wireless door lock function operates normally | A |
| Wireless door lock function does not operate normally | B |
A
B
Inspect the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG