Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY › from 2019.02
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0371434 FRONT PASSENGER AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 73960A 1.INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

a.
B525436C01
0,0 0,0 false
V113146

Hold Here


While holding the positions shown in the illustration, attach the instrument panel passenger airbag assembly hook near the rear of the vehicle to the airbag door wall near the rear of the vehicle.


b.
B525155C01
0,0 0,0 false
V113147

Install in this Direction


Slowly lower the instrument panel passenger airbag assembly to attach the instrument panel passenger airbag assembly hook near the front of the vehicle to the airbag door wall near the front of the vehicle.


c.
B525321

Install the 2 screws.


Hide 82142A 2.INSTALL NO. 2 INSTRUMENT PANEL WIRE

a.

for Dual Type:

i.
B525156C01
0.948,1.969 0.781,2.052 true 0.99,1.854 1.302,2.052 0.313,0.198 10 false *a 2.083,0.323 2.281,0.49 0.198,0.167 10 true *b 2.24,0.646 2.438,0.813 0.198,0.167 10 true *c
*a Lock Button
*b Wire Harness Clamp
*c Guide
V113147

Push


Attach the wire harness clamp and guide to install the No. 2 instrument panel wire.


ii.

Connect the 2 airbag connectors and push the lock button to lock.

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.

·

Be sure to connect the connectors to each corresponding color.

·

Make sure the lock button is securely locked.





b.

for Single Type:

i.
B525157C01
0.948,2.198 1.125,2.083 true 1.146,1.906 1.458,2.104 0.313,0.198 10 false *a 2.083,0.333 2.25,0.5 0.167,0.167 10 true *b 2.25,0.646 2.438,0.823 0.188,0.177 10 true *c
*a Lock Button
*b Wire Harness Clamp
*c Guide
V113147

Push


Attach the wire harness clamp and guide to install the instrument panel wire assembly.


ii.

Connect the airbag connector and push the lock button to lock.

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.

·

Make sure the lock button is securely locked.





Hide 55972C 3.INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT

Hide 55086 4.INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 55950G 5.INSTALL DEFROSTER NOZZLE ASSEMBLY

Hide 6.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 8.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 9.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 10.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 13.PERFORM SYSTEM INITIALIZATION AND CALIBRATION