Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY › 2019.02–2020.08
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0371434 FRONT PASSENGER AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel passenger airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 6.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 55950G 7.REMOVE DEFROSTER NOZZLE ASSEMBLY

Hide 55086 8.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 55972C 9.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

Hide 82142A 10.REMOVE NO. 2 INSTRUMENT PANEL WIRE

a.

for Dual Type:

i.
B525151C01
0.896,2.219 0.667,2.344 true 0.938,2.104 1.25,2.302 0.313,0.198 10 false *a 2.083,0.333 2.271,0.49 0.188,0.156 10 true *b 2.24,0.646 2.417,0.823 0.177,0.177 10 true *c
*a Lock Button
*b Wire Harness Clamp
*c Guide
V100155

Protective Tape
V113147

Release in this Direction


Using a screwdriver, release the lock button and disconnect the 2 airbag connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Tape the screwdriver tip before use.



ii.

Detach the wire harness clamp and guide and remove the No. 2 instrument panel wire.



b.

for Single Type:

i.
B525152C01
0.813,2.49 1.177,2.25 true 1.188,2.115 1.5,2.313 0.313,0.198 10 false *a 2.073,0.323 2.271,0.49 0.198,0.167 10 true *b 2.229,0.656 2.427,0.823 0.198,0.167 10 true *c
*a Lock Button
*b Wire Harness Clamp
*c Guide
V100155

Protective Tape
V113147

Release in this Direction


Using a screwdriver, release the lock button and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Tape the screwdriver tip before use.



ii.

Detach the wire harness clamp and guide and remove the No. 2 instrument panel wire.



Hide 73960A 11.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

CAUTION:
B399173C01
0,0 0,0 false
V100155

Deployment Side


·

When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.
B525321

Remove the 2 screws.


b.
B525153

Insert moulding remover B into the side of the airbag door facing the front of the vehicle and detach the hook.


c.
B525154C01
0,0 0,0 false
V113146

Hold Here
V113147

Move in this Direction


While holding the positions shown in the illustration, move the instrument panel passenger airbag assembly toward you, detach the hook near the rear of the vehicle, and then remove the instrument panel passenger airbag assembly.