Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR BELT MOULDING › 2019.02–2020.08
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377754 REAR DOOR BELT MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR BELT MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV Model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV Model) (Click here)
Reset back door close position Power back door system (for HV Model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline Model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline Model) (Click here)
Reset back door close position Power back door system (for Gasoline Model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.

·

When performing removal for the rear door belt moulding, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL




d.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 69278C 6.REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

Hide 74646A 7.REMOVE DOOR ASSIST GRIP COVER LH

Hide 8.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 67604 9.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 68174A 10.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

Hide 68199 11.REMOVE REAR DOOR REAR BELT SEAL LH

Hide 67842E 12.REMOVE REAR DOOR SERVICE HOLE COVER LH

Hide 67674A 13.REMOVE REAR DOOR FRAME GARNISH LH

Hide 68152C 14.DISCONNECT REAR DOOR GLASS RUN LH

Hide 67408E 15.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68124C 16.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

Hide 68104 17.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 75722A 18.REMOVE REAR DOOR BELT MOULDING LH

a.
B524024C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear door belt moulding LH.


b.
B524025C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


While pressing the rear door belt moulding LH, pull the edge and detach the claw as shown in the illustration.


c.
B524026C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw to remove the rear door belt moulding LH.