Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER (for 4WD/AWD) › 2019.02–2020.08
RM3620E _52 Drivetrain _076176 AXLE AND DIFFERENTIAL _0371993 REAR AXLE CARRIER(for 4WD/AWD) A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER(for 4WD/AWD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for HV model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for Gasoline model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.RELEASE PARKING BRAKE

Hide 2.REMOVE REAR WHEEL

Hide 48738C 3.REMOVE LOWER NO. 2 CONTROL ARM COVER (w/ Cover)

Hide 890C0A 4.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C397667

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




b.
C397676

Remove the bolt and disconnect the skid control sensor from the rear axle carrier sub-assembly.

NOTICE:
·

Keep the tip of the skid control sensor and installation hole free of foreign matter.

·

Do not rotate or apply excessive force to the skid control sensor when removing it from the rear axle carrier sub-assembly. Rotating or applying excessive force may result in damage to the skid control sensor.




c.
C405134

Remove the nut, disengage the 2 clamps and separate the No. 2 parking brake wire assembly from the rear flexible hose bracket and rear trailing arm assembly.


Hide 47319F 5.DISCONNECT REAR FLEXIBLE HOSE LH

a.
C412369

Remove the bolt and disconnect the rear flexible hose LH from the rear flexible hose bracket.


Hide 42312B 6.REMOVE REAR AXLE SHAFT NUT

Hide 7.DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH

a.
C407494

Remove the 2 bolts and disconnect the rear disc brake caliper assembly LH from the rear axle carrier sub-assembly.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake caliper assembly LH from hanging by the rear flexible hose.



Hide 42431 8.REMOVE REAR DISC

Hide 42450B 9.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 47352B 10.REMOVE NO. 2 FLEXIBLE HOSE BRACKET

a.
C397672

Remove the bolt and flexible hose bracket from the rear axle carrier sub-assembly.


Hide 89408C 11.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Hide 48840A 12.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Hide 48231B 13.REMOVE REAR COIL SPRING LH

Hide 48258C 14.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48720A 15.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C407499

Remove the bolt, nut and rear No. 1 suspension arm assembly LH from the rear axle carrier sub-assembly and rear suspension member sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 16.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

a.
C405157

Loosen the 3 bolts of the rear trailing arm assembly.


b.
C405095C01
1,0.656 1.25,0.656 1.25,0.656 1.427,0.979 true 0.708,0.573 0.979,0.802 0.271,0.229 10 true *1
*1 Rear Axle Carrier Pin


Loosen the nut of the rear shock absorber assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



c.
C405136C01
1.167,2.25 1.333,2.25 1.333,2.25 1.5,2.417 true 1.167,3 1.333,3 1.333,3 1.583,3.167 true 0.958,2.167 1.271,2.323 0.313,0.156 10 false *a 0.99,2.917 1.302,3.073 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Using a jack and wooden block, support the rear axle carrier sub-assembly.

NOTICE:
·

When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




d.
C405138N01
0.646,0.052 0.917,0.25 0.271,0.198 10 true *A

Loosen the bolt (A).

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Remove the 3 bolts, nut and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.


f.

Remove the nut and disconnect the rear shock absorber assembly from the rear axle carrier sub-assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



g.

Remove the bolt (A), nut and rear axle carrier sub-assembly from the rear upper control arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.