The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
58398F
2.REMOVE NO. 1 FLOOR UNDER COVER (for 4WD/AWD, w/ NO. 1 FLOOR UNDER COVER)
G3834
3.REMOVE SERVICE PLUG GRIP
G921F
4.REMOVE NO. 2 INVERTER PROTECTOR (for 4WD/AWD, w/ NO. 2 INVERTER PROTECTOR)
82111
5.DISCONNECT ENGINE ROOM MAIN WIRE
Be sure to wear insulated gloves.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
Move the lock lever while pushing the lock on the connector, and disconnect the inverter with converter assembly connector.
Do not damage the terminals, connector housing or inverter with converter assembly during disconnection.
Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
Insulate the disconnected terminals with insulating tape.
Do not touch the waterproof seal or terminals of the connector.
6.REMOVE CONNECTOR COVER ASSEMBLY
7.CHECK TERMINAL VOLTAGE
8.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY
821H1
9.DISCONNECT HV FLOOR UNDER WIRE
10.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
11.REMOVE REAR SEAT CUSHION LOCK HOOK
67918E
12.REMOVE REAR DOOR SCUFF PLATE LH
58467H
13.REMOVE NO. 3 BATTERY SERVICE COVER BOARD
67917C
14.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
58466J
15.REMOVE NO. 2 BATTERY SERVICE COVER BOARD
58464D
16.REMOVE BATTERY SERVICE COVER BOARD
71033
17.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
G92N4A
18.REMOVE NO. 1 HV BATTERY COVER PANEL RH
821H1
19.DISCONNECT HV FLOOR UNDER WIRE
Be sure to wear insulated gloves.
| *a | Shield Ground |
Disconnect the 2 HV battery junction block assembly connectors.
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
Disconnect the shield ground from the HV battery.
Disengage the 3 claws to remove the No. 4 relay block cover.
Remove the nut.
Disengage the clamp.
Disengage the clamp and disconnect HV floor under wire.
53896B
20.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
53895B
21.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
51441
22.REMOVE NO. 1 ENGINE UNDER COVER
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
51420
23.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
51468B
24.REMOVE ENGINE UNDER COVER HEAT INSULATOR
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
58166A
25.REMOVE FRONT FLOOR COVER LH
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
58165C
26.REMOVE FRONT FLOOR COVER RH
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
58167A
27.REMOVE FRONT CENTER FLOOR COVER
Remove the 2 clips and front center floor cover.
58153E
28.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR
Remove the 2 nuts, clip and front No. 2 floor heat insulator.
58152A
29.REMOVE FRONT LOWER NO. 1 FLOOR HEAT INSULATOR
Remove the nut, bolt, clip and front lower No. 1 floor heat insulator.
58151
30.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
Remove the 2 nuts and front No. 1 floor heat insulator.
58724F
31.REMOVE NO. 2 ENGINE SERVICE COVER CUSHION
Remove the 2 nuts and No. 2 engine service cover cushion.
58723E
32.REMOVE ENGINE SERVICE COVER CUSHION
Remove the 2 nuts and engine service cover cushion.
33820B
33.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Remove the nut and disconnect the transmission control cable assembly.
17410
34.REMOVE FRONT EXHAUST PIPE ASSEMBLY
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL
17141
35.REMOVE EXHAUST MANIFOLD
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL
77100
36.REMOVE FUEL TANK ASSEMBLY
for A25A-FXS, w/ Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL TANK (w/ Canister Pump Module)>REMOVAL
for A25A-FXS, w/o Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL TANK (w/o Canister Pump Module)>REMOVAL
for A25B-FXS:
Click hereEngine / Hybrid System>A25B-FXS (FUEL)>FUEL TANK>REMOVAL
821H1
37.REMOVE HV FLOOR UNDER WIRE
Be sure to wear insulated gloves.
Insulate the disconnected connectors with insulating tape.
| *A | for 2WD |
| *B | for 4WD/AWD |
|
Bolt |
|
Nut |
for 2WD:
Remove the 2 nuts.
for 4WD/AWD:
Remove the 2 nuts snd 2 bolts.
Disengage the grommet and pull out the HV floor under wire from the floor panel hole.
Remove the 3 bolts and nut.
Remove the 2 stud clamps.
If the stud clamps are removed forcibly, the stud bolts may be damaged.
Remove the 2 nuts, bolt and 2 stud clamps.
If the stud clamps is removed forcibly, the stud bolt may be damaged.
|
Remove in this Direction |
Disengage the 2 claws.
Disengage the guide and disconnect the No. 1 terminal cap.
Remove the nut and disconnect the engine room main wire.
Remove the 2 nuts and HV floor under wire.
for 4WD/AWD:
Disengage the clamp.
| *a | Waterproof Seal |
Remove the 2 bolts and HV floor under wire from the rear traction motor with transaxle assembly.
Do not damage the terminals, interlock connector or rear traction motor with transaxle assembly during disconnection.
Do not touch the waterproof seal or terminals of the connector.
Do not allow any foreign matter or water to enter the rear traction motor with transaxle assembly.
Although the connector may feel loose, this is not due to a malfunction.