Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model) › from 2019.02
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0370842 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  B1448  Passenger Side FACE Servo Motor Circuit  


DESCRIPTION

The No. 3 air conditioning radiator damper servo sub-assembly (front passenger side mode) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the No. 3 air conditioning radiator damper servo sub-assembly (front passenger side mode) to the appropriate position, which controls the air outlet switching.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1448 Passenger Side FACE Servo Motor Circuit
·

Diagnosis condition: During No. 3 air conditioning radiator damper servo sub-assembly (front passenger side mode) operation

·

Malfunction status: The damper servo operation request signal is output but the position information of the servo does not change or servo is malfunctioning

·

Detection time: Continuously for 30 seconds or more


·

No. 3 air conditioning radiator damper servo sub-assembly (front passenger side mode)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly

·

Air conditioning radiator assembly


Memorized

DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition*1 No. 3 air conditioning radiator damper servo sub-assembly (front passenger side mode) operating ○ ○
Diagnosis Condition*2 No. 3 air conditioning radiator damper servo sub-assembly operating ○ ○
Malfunction Air outlet damper servo operation request signals are output but the air outlet damper position sensor value does not change ○ -
Air outlet damper servo operation request signals are output but the air outlet damper position sensor value is abnormal - ○
Detection Time Continuously for 30 seconds or more Continuously for 30 seconds or more
Trip Count 1 trip 1 trip

HINT:

If the conditions of either of these patterns are detected, a DTC will be stored.


WIRING DIAGRAM

E315725E41
5.198,0.75 5.969,0.948 0.771,0.198 10 false BUS 5.219,1.135 5.99,1.333 0.771,0.198 10 false B BUS 5.219,1.531 5.99,1.729 0.771,0.198 10 false BUS G 4.99,0.698 5.26,0.896 0.271,0.198 10 false 3 5,1.135 5.271,1.333 0.271,0.198 10 false 4 5,1.531 5.271,1.729 0.271,0.198 10 false 2 3.25,2.073 4.802,2.531 1.552,0.458 10 false Air Conditioning Harness Assembly 5.188,2.323 6.021,2.521 0.833,0.198 10 false z11 5.188,2.479 6.75,2.969 1.563,0.49 10 false Air Conditioning Amplifier Assembly 0.771,2.219 2.667,2.74 1.896,0.521 10 false No. 3 Air Conditioning Radiator Damper Servo Sub-assembly 6.021,0.865 6.406,1.063 0.385,0.198 10 false IC 0.667,3.344 2.927,3.615 2.26,0.271 10 false : LIN Communication Line 0.875,1.115 1.948,1.479 1.073,0.365 10 false Front Passenger Side Mode 6.521,1.125 6.906,1.323 0.385,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

Confirm that no mechanical problems are present because this DTC can be stored when either a damper link or damper is mechanically locked.

·

When installing the servo motor, make sure to install it correctly.

·

When the servo motor is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>INITIALIZATION



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Proceed to
OK
NG



OK

2.CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

2.CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
a.

Check that the No. 3 air conditioning radiator damper servo sub-assembly is installed correctly.

OK:

No. 3 air conditioning radiator damper servo sub-assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER)

NG

3.CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER)
a.

Check for a wire harness caught between the links of the motors and dampers.

OK:

No wire harnesses are caught between the links of the motors and dampers.



Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING RADIATOR ASSEMBLY (DAMPER)

NG

REMOVE PINCHED WIRE HARNESS

4.CHECK AIR CONDITIONING RADIATOR ASSEMBLY (DAMPER)

b.

Operate the dampers by hand.

OK:

The dampers are easily operated by hand.



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE AIR CONDITIONING RADIATOR ASSEMBLY

5.CHECK NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
a.

Interchange the No. 3 air conditioning radiator damper servo sub-assembly (front passenger side mode) with the No. 1 air conditioning radiator damper servo sub-assembly (driver side mode) and connect the connectors to them.



b.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

c.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
Result:
Result Proceed to
DTC B1443 is output A
DTC B1448 is output B
DTC B1443 and B1448 are not output C


HINT:

Codes other than DTC B1443 and B1448 may be output at this time, but they are not related to this check.




A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C