Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2019.02–2020.08
RM3620E _58 Vehicle Interior _076046 DOOR LOCK _0377380 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Power window regulator motor assembly LH

·

Power window regulator motor assembly RH

·

Rear door window regulator sub-assembly LH

·

Rear door window regulator sub-assembly RH

·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Power window regulator motor assembly LH

·

Power window regulator motor assembly RH

·

Rear door window regulator assembly LH

·

Rear door window regulator assembly RH

·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH

·

Rear door No. 3 glass run LH

·

Rear door No. 3 glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.

·

When performing disassembly for the rear door, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL




d.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 69278C 6.REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

Hide 74646A 7.REMOVE DOOR ASSIST GRIP COVER LH

Hide 8.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 67604 9.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 68174A 10.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

Hide 68197A 11.REMOVE REAR DOOR FRONT BELT SEAL LH

Hide 68199 12.REMOVE REAR DOOR REAR BELT SEAL LH

Hide 67842E 13.REMOVE REAR DOOR SERVICE HOLE COVER LH

Hide 67674A 14.REMOVE REAR DOOR FRAME GARNISH LH

Hide 68152C 15.DISCONNECT REAR DOOR GLASS RUN LH

Hide 67408E 16.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68152C 17.REMOVE REAR DOOR GLASS RUN LH

Hide 68104 18.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 69804 19.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

Hide 69060A 20.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

a.
B522644C01
2.094,0.375 2.344,0.292 true 2.385,0.177 2.635,0.396 0.25,0.219 10 true *a
*a Release Plate
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, remove the 3 "TORX" screws.


b.

Remove the release plate of the rear door outside handle frame sub-assembly LH in the direction indicated by the arrow shown in the illustration to remove the rear door lock with motor assembly LH.


Hide 69318D 21.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)

a.
B522645

When reusing rear door lock with motor assembly LH:

i.

Remove the door lock wiring harness seal from the rear door lock with motor assembly LH.



Hide 69038A 22.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)

a.
B522646C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the rear door lock cover sub-assembly LH.


b.
B522647

Detach the claw and remove the rear door lock cover sub-assembly LH.


Hide 69740E 23.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

a.
B522648C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp and remove the rear door lock remote control cable assembly as shown in the illustration.


Hide 69780E 24.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

a.
B522649C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp and remove the rear door inside locking cable assembly as shown in the illustration.


Hide 69060A 25.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

a.
B532305C01
2.729,2.49 3,2.292 true 3,2.167 3.198,2.354 0.198,0.188 10 true *a
*a Release Plate
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, remove the 3 "TORX" screws.


b.

Remove the release plate of the rear door outside handle frame sub-assembly LH in the direction indicated by the arrow shown in the illustration to remove the rear door lock with motor assembly LH.


Hide 69318D 26.REMOVE DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)

a.
B532306

When reusing rear door lock with motor assembly LH:

i.

Remove the door lock wiring harness seal from the rear door lock with motor assembly LH.



Hide 69740E 27.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

a.
B532307C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the cover.


b.
B532309C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp and remove the rear door lock remote control cable assembly as shown in the illustration.


Hide 69780E 28.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

a.
B532318C01
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the cover.


b.
B532310C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp and remove the rear door inside locking cable assembly as shown in the illustration.