Home › Vehicle Exterior › DOOR / HATCH › KICK SENSOR › 2019.02–2020.08
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0377475 KICK SENSOR A

DOOR / HATCH  KICK SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the kick door control sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Rear bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for HV model) (Click here)
Kick door control sensor Reset connection history There are cases where the connection history display differs from the vehicle condition (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Removal and installation of auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Rear bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Kick door control sensor Reset connection history There are cases where the connection history display differs from the vehicle condition (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL




d.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 52159 6.REMOVE REAR BUMPER COVER

Hide 891B1 7.REMOVE KICK DOOR CONTROL BRACKET

a.
B523040

Disconnect the connector.

NOTICE:

Do not touch the terminal of the kick door control sensor connector.



b.

Remove the 3 screws.

B523041C01
0,0 0,0 false
V113147

Remove in this Direction
V100135

Screw
V100136

Clip - -



c.

Remove the 2 clips and kick door control bracket together with the kick door control sensor.


Hide 891B2 8.REMOVE KICK DOOR CONTROL SENSOR

a.

Detach the claw and guide and disconnect the antenna cable in the order shown in the illustration.

B523042N01
0.75,2.281 0.969,2.479 0.219,0.198 10 true (1) 1.667,2.063 1.885,2.26 0.219,0.198 10 true (2) 2.656,1.854 2.875,2.052 0.219,0.198 10 true (3) 3.76,1.656 3.979,1.854 0.219,0.198 10 true (4) 4.542,1.5 4.76,1.698 0.219,0.198 10 true (5) 5.229,1 5.448,1.198 0.219,0.198 10 true (6) 1.281,2.354 1.5,2.552 0.219,0.198 10 true (7) 1.896,2.26 2.115,2.458 0.219,0.198 10 true (8) 2.927,2.031 3.146,2.229 0.219,0.198 10 true (9) 3.865,1.854 4.146,2.052 0.281,0.198 10 true (10) 4.667,1.667 4.948,1.865 0.281,0.198 10 true (11) 5.354,1.76 5.635,1.958 0.281,0.198 10 true (12)


b.
B523043

Detach the clamp.

NOTICE:
·

Do not pull strongly on the wire.

·

Do not twist the wire.




c.
B523044C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw in the direction indicated by the arrow as shown in the illustration.


d.
B523045C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and remove the kick door control sensor from the kick door control bracket in the direction indicated by the arrow shown in the illustration.

NOTICE:
·

Do not subject the kick door control sensor to strong impacts or force, and do not drop it.

·

Do not reuse a kick door control sensor which has been subjected to an impact or dropped.