Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster) › 2019.02–2019.09
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1235  Foreign Object is Attached on Tip of Front Speed Sensor RH  C1236  Foreign Object is Attached on Tip of Front Speed Sensor LH  C1238  Foreign Object is Attached on Tip of Rear Speed Sensor RH  C1239  Foreign Object is Attached on Tip of Rear Speed Sensor LH  C1275  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1277  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

When foreign matter adheres to a speed sensor tip or speed sensor rotor, these DTCs are stored. The presence of foreign matter can be judged when an abnormal waveform is received from a sensor.

These DTCs may also be detected when a malfunction occurs in the connector terminals or wire harness of the speed sensor circuit.

DTCs C1275 to C1278 will be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs from C1275 to C1278 are output only in Test Mode.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1235 Foreign Object is Attached on Tip of Front Speed Sensor RH 541 Either of the following is detected:
1.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign matter attached)

·

Foreign matter attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit


-
C1236 Foreign Object is Attached on Tip of Front Speed Sensor LH 542 Either of the following is detected:
1.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign matter attached)

·

Foreign matter attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit


-
C1238 Foreign Object is Attached on Tip of Rear Speed Sensor RH 543 Either of the following is detected:
1.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign matter attached)

·

Foreign matter attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit


-
C1239 Foreign Object is Attached on Tip of Rear Speed Sensor LH 544 Either of the following is detected:
1.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

2.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.


·

Speed sensor rotor malfunction (foreign matter attached)

·

Foreign matter attached to speed sensor

·

Open or short in speed sensor

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Resistance in speed sensor circuit


-
C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.
·

Front speed sensor RH

·

Front speed sensor rotor RH (Front axle hub sub-assembly RH)


-
C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.
·

Front speed sensor LH

·

Front speed sensor rotor LH (Front axle hub sub-assembly LH)


-
C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)*1

·

Rear speed sensor RH*2

·

Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH)


-
C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)*1

·

Rear speed sensor LH*2

·

Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH)


-

*1: for 2WD

*2: for 4WD/AWD

DTC Detection Conditions: C1235
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more ○ -
At a vehicle speed of 10 km/h (6 mph) or more - ○
Malfunction Status Noise occurs on the speed sensor signal waveform ○ -
Noise occurs once per wheel revolution - ○
Detection Time 5 seconds or more 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1236
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more ○ -
At a vehicle speed of 10 km/h (6 mph) or more - ○
Malfunction Status Noise occurs on the speed sensor signal waveform ○ -
Noise occurs once per wheel revolution - ○
Detection Time 5 seconds or more 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1238
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more ○ -
At a vehicle speed of 10 km/h (6 mph) or more - ○
Malfunction Status Noise occurs on the speed sensor signal waveform ○ -
Noise occurs once per wheel revolution - ○
Detection Time 5 seconds or more 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1239
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition At a vehicle speed of 20 km/h (12 mph) or more ○ -
At a vehicle speed of 10 km/h (6 mph) or more - ○
Malfunction Status Noise occurs on the speed sensor signal waveform ○ -
Noise occurs once per wheel revolution - ○
Detection Time 5 seconds or more 15 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


PROCEDURE

1.CHECK DTC
a.

Check that no speed sensor malfunction DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

When C1464, C1465, C1466, and/or C1467 are output together with C1235, C12366, C1238, and/or C1239, inspect and repair the trouble areas indicated by C1464, C1465, C1466, and/or C1467 first.



Result:
Result Proceed to
DTCs C1235 and/or C1236 are output. A
DTCs C1238 and C1239 are output. B
Speed sensor malfunction DTCs (C1464, C1465, C1466 and/or C1467) are output. C



A

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)

B

5.INSPECT PARKING BRAKE WIRE ASSEMBLY

C

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A91 or A92 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A42-18 (FR+) - A91-1 (FR+) Always Below 1 Ω
A42-18 (FR+) or A91-1 (FR+) - Body ground Always 10 kΩ or higher
A42-5 (FR-) - A91-2 (FR-) Always Below 1 Ω
A42-5 (FR-) or A91-2 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A42-31 (FL+) - A92-1 (FL+) Always Below 1 Ω
A42-31 (FL+) or A92-1 (FL+) - Body ground Always 10 kΩ or higher
A42-32 (FL-) - A92-2 (FL-) Always Below 1 Ω
A42-32 (FL-) or A92-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SPEED SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FRONT SPEED SENSOR
a.

Check the speed sensor tip.

OK:

The sensor tip is free of oil and foreign matter.



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AXLE HUB SUB-ASSEMBLY

NG

CLEAN FRONT SPEED SENSOR

4.CHECK FRONT AXLE HUB SUB-ASSEMBLY
a.

Check the speed sensor rotor (front axle hub sub-assembly).

OK:

The speed sensor rotor is free of scratches, oil, and foreign matter.


HINT:

The speed sensor rotor is incorporated into the front axle hub sub-assembly.



Result:
Result Proceed to
OK A
Foreign matter and oil present B
Damage present C



A

B

CLEAN SPEED SENSOR ROTOR

C

REPLACE FRONT AXLE HUB SUB-ASSEMBLY

5.INSPECT PARKING BRAKE WIRE ASSEMBLY
a.
C405858C01
0.823,0.427 1.125,0.677 0.302,0.25 0.823,0.75 1.125,1 0.302,0.25 2.323,0.406 2.688,0.656 0.365,0.25 2.333,0.708 2.677,0.958 0.344,0.25 0.469,2.479 0.844,1.906 true 1.458,2.521 1.083,1.896 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *1 0.844,0.479 1.156,0.677 0.313,0.198 10 false M50 0.854,0.792 1.167,0.99 0.313,0.198 10 false N58 1.219,0.479 1.531,0.677 0.313,0.198 10 false *A 1.219,0.792 1.531,0.99 0.313,0.198 10 false *B 2.365,0.458 2.75,0.635 0.385,0.177 10 false MM2 2.365,0.76 2.729,0.958 0.365,0.198 10 false NN2 2.75,0.771 3.063,0.969 0.313,0.198 10 false *B 2.76,0.458 3.073,0.656 0.313,0.198 10 false *A 0.302,2.5 0.625,2.719 0.323,0.219 10 false RA- 1.458,2.573 1.823,2.802 0.365,0.229 10 false RA+ 0.906,1.104 1.219,1.302 0.313,0.198 10 false *a 2.438,1.094 2.75,1.292 0.313,0.198 10 false *b 0.302,2.75 0.625,2.969 0.323,0.219 10 false LA- 1.458,2.792 1.823,3.021 0.365,0.229 10 false LA+ 1.771,2.594 2.083,2.792 0.313,0.198 10 false *A 0.604,2.521 0.917,2.719 0.313,0.198 10 false *A 0.594,2.771 0.906,2.969 0.313,0.198 10 false *B 1.75,2.823 2.063,3.021 0.313,0.198 10 false *B
*A for RH
*B for LH
*1 Skid Control Sensor Wire (Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the M50 or N58 skid control sensor wire (parking brake wire assembly) connector.


c.

Disconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
M50-2 (RA+) - MM2-3 Always Below 1 Ω
M50-2 (RA+) or MM2-3 - Body ground and other terminals Always 10 kΩ or higher
M50-1 (RA-) - MM2-4 Always Below 1 Ω
M50-1 (RA-) or MM2-4 - Body ground and other terminals Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
N58-2 (LA+) - NN2-3 Always Below 1 Ω
N58-2 (LA+) or NN2-3 - Body ground and other terminals Always 10 kΩ or higher
N58-1 (LA-) - NN2-4 Always Below 1 Ω
N58-1 (LA-) or NN2-4 - Body ground and other terminals Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR SPEED SENSOR)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR SPEED SENSOR)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Reconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.


c.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A42-22 (RR+) - M50-2 (RA+) Always Below 1 Ω
A42-22 (RR+) or M50-2 (RA+) - Body ground Always 10 kΩ or higher
A42-9 (RR-) - M50-1 (RA-) Always Below 1 Ω
A42-9 (RR-) or M50-1 (RA-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A42-20 (RL+) - N58-2 (LA+) Always Below 1 Ω
A42-20 (RL+) or N58-2 (LA+) - Body ground Always 10 kΩ or higher
A42-7 (RL-) - N58-1 (LA-) Always Below 1 Ω
A42-7 (RL-) or N58-1 (LA-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for 2WD)
OK (for 4WD/AWD)
NG



OK (for 2WD)

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

OK (for 4WD/AWD)

7.CHECK REAR SPEED SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK REAR SPEED SENSOR
a.

Check the speed sensor tip.

OK:

The sensor tip is free of oil and foreign matter.



Result:
Proceed to
OK
NG



OK

8.CHECK REAR AXLE HUB SUB-ASSEMBLY

NG

CLEAN REAR SPEED SENSOR

8.CHECK REAR AXLE HUB SUB-ASSEMBLY
a.

Check the speed sensor rotor (rear axle hub sub-assembly).

OK:

The speed sensor rotor is free of scratches, oil, and foreign matter.


HINT:

The speed sensor rotor is incorporated into the rear axle hub sub-assembly.



Result:
Result Proceed to
OK A
Foreign matter and oil present B
Damage present C



A

B

CLEAN SPEED SENSOR ROTOR

C

REPLACE REAR AXLE HUB SUB-ASSEMBLY