Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster) › 2019.02–2019.09
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1466  Rear Speed Sensor RH Circuit  C1467  Rear Speed Sensor LH Circuit  


DESCRIPTION

Each speed sensor detects the wheel speed and sends the signals to the skid control ECU (brake booster with master cylinder assembly). These signals are used for ABS control.

DTCs C1273 and C1274 are cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1273 and C1274 are output only in Test Mode.

C269035E25
1.833,1.083 1.833,0.583 false 1.583,0.583 1.833,0.583 false 5,1.25 5,0.583 false 5,0.583 4.75,0.583 false 0.573,0.167 1.646,0.354 1.073,0.188 12 false for 2WD: 3.802,0.167 4.917,0.375 1.115,0.208 12 false for 4WD/AWD: 0.688,0.542 1.76,0.74 1.073,0.198 10 false Speed Sensor 3.885,0.552 4.958,0.75 1.073,0.198 10 false Speed Sensor 1.281,2.406 2.542,2.594 1.26,0.188 10 false Speed Sensor Rotor 4.635,2.406 5.906,2.594 1.271,0.188 10 false Speed Sensor Rotor 4.833,3.385 5.448,3.583 0.615,0.198 10 false 1.4 V 4.833,3.75 5.448,3.948 0.615,0.198 10 false 0.7 V 3.708,4.188 4.427,4.396 0.719,0.208 10 false High speed 2.792,4.083 3.49,4.281 0.698,0.198 10 false Low speed

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)*1

·

Rear speed sensor RH*2

·

Sensor installation

·

Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH)


-
C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.
·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)*1

·

Rear speed sensor LH*2

·

Sensor installation

·

Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH)


-
C1466 Rear Speed Sensor RH Circuit 521
522
523
524
526
527
528
529
·

INF Code: 521

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 522

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.



·

INF Code: 523

-

An open is detected in the speed sensor signal circuit for 0.5 seconds or more.



·

INF Code: 524

-

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 526

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 527

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 528

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 529

-

Speed sensor output is 270 km/h (167 mph) or more continuously for 5 seconds or more.



·

INF Code: 521, 522, 524, 527

-

Open or short in speed sensor


-

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Rear speed sensor RH (Rear axle hub and bearing assembly RH)*1


-

Rear speed sensor RH*2


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 523

-

Open or short in speed sensor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Rear speed sensor RH (Rear axle hub and bearing assembly RH)*1


-

Rear speed sensor RH*2


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 526, 528

-

Open or short in wire harness


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 529

-

Open or short in speed sensor


-

Open or short in wire harness


-

Rear speed sensor RH (Rear axle hub and bearing assembly RH)


-

Skid control ECU (Brake booster with master cylinder assembly)



-
C1467 Rear Speed Sensor LH Circuit 531
532
533
534
536
537
538
539
·

INF Code: 531

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 532

-

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more.



·

INF Code: 533

-

An open is detected in the speed sensor signal circuit for 0.5 seconds or more.



·

INF Code: 534

-

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 536

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 537

-

At a vehicle speed of 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 538

-

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 539

-

Speed sensor output is 270 km/h (167 mph) or more continuously for 5 seconds or more.



·

INF Code: 531, 532, 534, 537

-

Open or short in speed sensor


-

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Rear speed sensor LH (Rear axle hub and bearing assembly LH)*1


-

Rear speed sensor LH*2


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 533

-

Open or short in speed sensor


-

Open or short in wire harness


-

Improperly connected connector, deformation or corrosion of terminals


-

Rear speed sensor LH (Rear axle hub and bearing assembly LH)*1


-

Rear speed sensor LH*2


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 536, 538

-

Open or short in wire harness


-

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 539

-

Open or short in speed sensor


-

Open or short in wire harness


-

Rear speed sensor LH (Rear axle hub and bearing assembly LH)


-

Skid control ECU (Brake booster with master cylinder assembly)



-

*1: for 2WD

*2: for 4WD/AWD

WIRING DIAGRAM

C403535E04
6,0.615 6.458,0.813 0.458,0.198 10 false RR+ 1.219,0.729 1.677,0.927 0.458,0.198 10 false RA+ 1.26,2.979 1.688,3.167 0.427,0.188 10 false RA+ 6,1.302 6.458,1.5 0.458,0.198 10 false RR- 1.24,1.417 1.698,1.615 0.458,0.198 10 false RA- 1.281,3.531 1.615,3.719 0.333,0.188 10 false RA- 5.708,0.604 6.021,0.802 0.313,0.198 10 false 22 5.771,1.302 6.083,1.5 0.313,0.198 10 false 9 1.719,0.521 2.031,0.719 0.313,0.198 10 false 2 1.729,1.208 2.042,1.406 0.313,0.198 10 false 1 1.74,2.74 2.052,2.938 0.313,0.198 10 false 2 1.729,3.333 2.042,3.531 0.313,0.198 10 false 1 3.177,2.969 3.635,3.167 0.458,0.198 10 false MM2 3.177,3.542 3.635,3.74 0.458,0.198 10 false MM2 1.656,2.969 2.115,3.167 0.458,0.198 10 false M50 1.656,3.542 2.115,3.74 0.458,0.198 10 false M50 0,1.833 2.146,2.208 2.146,0.375 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 2.188,3.958 4.406,4.323 2.219,0.365 10 false Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly) 4.104,0.573 4.417,0.771 0.313,0.198 10 false *1 4.083,1.271 4.396,1.469 0.313,0.198 10 false *1 4.115,2.813 4.427,3.01 0.313,0.198 10 false *2 4.135,3.417 4.448,3.615 0.313,0.198 10 false *2 6,4.854 6.458,5.052 0.458,0.198 10 false RL+ 1.26,4.99 1.719,5.188 0.458,0.198 10 false LA+ 1.271,7.177 1.604,7.365 0.333,0.188 10 false LA+ 6.01,5.542 6.469,5.74 0.458,0.198 10 false RL- 1.281,5.656 1.74,5.854 0.458,0.198 10 false LA- 1.271,7.688 1.625,7.896 0.354,0.208 10 false LA- 4.125,4.844 4.438,5.042 0.313,0.198 10 false *1 4.146,7 4.458,7.198 0.313,0.198 10 false *2 4.167,7.573 4.479,7.771 0.313,0.198 10 false *2 4.146,5.542 4.458,5.74 0.313,0.198 10 false *1 5.708,4.844 5.896,5.042 0.188,0.198 10 false 20 5.76,5.531 6.021,5.781 0.26,0.25 10 false 7 1.74,4.781 1.896,4.979 0.156,0.198 10 false 2 1.729,5.396 1.885,5.594 0.156,0.198 10 false 1 3.167,7.125 3.625,7.323 0.458,0.198 10 false NN2 3.188,7.698 3.646,7.896 0.458,0.198 10 false NN2 1.656,7.125 2.115,7.323 0.458,0.198 10 false N58 1.667,7.698 2.125,7.896 0.458,0.198 10 false N58 1.74,6.875 1.896,7.073 0.156,0.198 10 false 2 1.708,7.438 1.865,7.635 0.156,0.198 10 false 1 0.052,6.031 2.156,6.427 2.104,0.396 10 false Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH) 1.979,8.125 4.188,8.51 2.208,0.385 10 false Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly) 5.583,8.01 6.042,8.208 0.458,0.198 10 false A42 5.583,8.156 7.156,8.75 1.573,0.594 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.323,8.458 5.552,8.656 1.229,0.198 10 false *2: for 4WD/AWD 4.323,8.156 5.552,8.354 1.229,0.198 10 false *1: for 2WD 0.094,3.958 1.563,4.135 1.469,0.177 10 false Rear Speed Sensor RH 3.281,0.521 3.594,0.719 0.313,0.198 10 false 3 3.271,1.219 3.583,1.417 0.313,0.198 10 false 4 2.24,1.844 4.448,2.208 2.208,0.365 10 false Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly) 0.104,8.115 1.635,8.292 1.531,0.177 10 false Rear Speed Sensor LH 2.313,6.063 4.521,6.417 2.208,0.354 10 false Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly) 1.677,4.99 2.135,5.188 0.458,0.198 10 false N58 1.667,5.667 2.125,5.865 0.458,0.198 10 false N58 3.167,4.99 3.625,5.188 0.458,0.198 10 false NN2 3.167,5.656 3.625,5.854 0.458,0.198 10 false NN2 1.667,0.74 2.125,0.938 0.458,0.198 10 false M50 1.646,1.438 2.104,1.635 0.458,0.198 10 false M50 3.177,0.74 3.635,0.938 0.458,0.198 10 false MM2 3.177,1.438 3.635,1.635 0.458,0.198 10 false MM2 3.292,3.292 3.604,3.49 0.313,0.198 10 false 4 3.281,2.75 3.594,2.948 0.313,0.198 10 false 3 3.25,5.427 3.563,5.625 0.313,0.198 10 false 4 3.25,7.438 3.563,7.635 0.313,0.198 10 false 4 3.25,6.896 3.563,7.094 0.313,0.198 10 false 3 3.25,4.771 3.563,4.969 0.313,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Error or Normal Normal: Momentary interruption not detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
RL Speed Open Rear speed sensor LH open detection Error or Normal Error: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Error" to "Normal".
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

b.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG (for 2WD)
NG (for 4WD/AWD)



OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG (for 2WD)

5.CHECK REAR SPEED SENSOR INSTALLATION

NG (for 4WD/AWD)

9.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the power switch off.


b.

Perform the sensor check in Test Mode Procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 1003
OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the power switch off.



c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1466 and C1467 are not output. A
DTCs C1466 and/or C1467 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR




A

B

6.INSPECT PARKING BRAKE WIRE ASSEMBLY
5.CHECK REAR SPEED SENSOR INSTALLATION
a.
C210569C09
1,1.167 1.313,1.521 false 1.385,1.49 1.698,1.646 0.313,0.156 10 false *a 0.896,1.74 1.208,1.896 0.313,0.156 10 false *b 2.396,1.75 2.708,1.948 0.313,0.198 10 false *c
*a No clearance
*b OK
*c NG


Turn the power switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and rear axle hub.



Result:
Proceed to
OK
NG



OK

6.INSPECT PARKING BRAKE WIRE ASSEMBLY

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

6.INSPECT PARKING BRAKE WIRE ASSEMBLY
a.
C405858C01
0.823,0.427 1.125,0.677 0.302,0.25 0.823,0.75 1.125,1 0.302,0.25 2.323,0.406 2.688,0.656 0.365,0.25 2.333,0.708 2.677,0.958 0.344,0.25 0.469,2.479 0.844,1.906 true 1.458,2.521 1.083,1.896 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *1 0.844,0.479 1.156,0.677 0.313,0.198 10 false M50 0.854,0.792 1.167,0.99 0.313,0.198 10 false N58 1.219,0.479 1.531,0.677 0.313,0.198 10 false *A 1.219,0.792 1.531,0.99 0.313,0.198 10 false *B 2.365,0.458 2.75,0.635 0.385,0.177 10 false MM2 2.365,0.76 2.729,0.958 0.365,0.198 10 false NN2 2.75,0.771 3.063,0.969 0.313,0.198 10 false *B 2.76,0.458 3.073,0.656 0.313,0.198 10 false *A 0.302,2.5 0.625,2.719 0.323,0.219 10 false RA- 1.458,2.573 1.823,2.802 0.365,0.229 10 false RA+ 0.906,1.104 1.219,1.302 0.313,0.198 10 false *a 2.438,1.094 2.75,1.292 0.313,0.198 10 false *b 0.302,2.75 0.625,2.969 0.323,0.219 10 false LA- 1.458,2.792 1.823,3.021 0.365,0.229 10 false LA+ 1.771,2.594 2.083,2.792 0.313,0.198 10 false *A 0.604,2.521 0.917,2.719 0.313,0.198 10 false *A 0.594,2.771 0.906,2.969 0.313,0.198 10 false *B 1.75,2.823 2.063,3.021 0.313,0.198 10 false *B
*A for RH
*B for LH
*1 Skid Control Sensor Wire (Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the M50 or N58 skid control sensor wire (parking brake wire assembly) connector.


c.

Disconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
M50-2 (RA+) - MM2-3 Always Below 1 Ω
M50-2 (RA+) or MM2-3 - Body ground and other terminals Always 10 kΩ or higher
M50-1 (RA-) - MM2-4 Always Below 1 Ω
M50-1 (RA-) or MM2-4 - Body ground and other terminals Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
N58-2 (LA+) - NN2-3 Always Below 1 Ω
N58-2 (LA+) or NN2-3 - Body ground and other terminals Always 10 kΩ or higher
N58-1 (LA-) - NN2-4 Always Below 1 Ω
N58-1 (LA-) or NN2-4 - Body ground and other terminals Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR SPEED SENSOR)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR SPEED SENSOR)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Reconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.


c.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A42-22 (RR+) - M50-2 (RA+) Always Below 1 Ω
A42-22 (RR+) or M50-2 (RA+) - Body ground Always 10 kΩ or higher
A42-9 (RR-) - M50-1 (RA-) Always Below 1 Ω
A42-9 (RR-) or M50-1 (RA-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A42-20 (RL+) - N58-2 (LA+) Always Below 1 Ω
A42-20 (RL+) or N58-2 (LA+) - Body ground Always 10 kΩ or higher
A42-7 (RL-) - N58-1 (LA-) Always Below 1 Ω
A42-7 (RL-) or N58-1 (LA-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C233859C92
0.646,0.521 1.135,0.813 0.49,0.292 2,0.521 2.49,0.813 0.49,0.292 0.969,1.344 1.177,1.781 true 2.323,1.344 2.531,1.781 true 1.188,1.813 1.583,2.052 0.396,0.24 10 false RA+ 2.552,1.823 2.979,2.031 0.427,0.208 10 false LA+ 0.135,0.083 0.323,0.24 0.188,0.156 10 false *a 0.76,0.594 1.052,0.75 0.292,0.156 10 false M50 2.125,0.594 2.573,0.792 0.448,0.198 10 false N58 0.427,0.583 0.74,0.781 0.313,0.198 10 false *A 1.771,0.573 2.083,0.771 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor (Rear Axle Hub and Bearing Assembly))


Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
M50-2 (RA+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
N58-2 (LA+) - Body ground Power switch on (IG) 5.7 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG

9.CHECK REAR SPEED SENSOR INSTALLATION
a.
C168336C26
0.906,1.49 1.26,1.854 false 0.688,0.385 1,0.583 0.313,0.198 10 false *b 2.26,0.385 2.573,0.583 0.313,0.198 10 false *c 1.406,1.885 1.719,2.083 0.313,0.198 10 false *a
*a No clearance
*b OK
*c NG


Turn the power switch off.


b.

Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for 4WD/AWD)>INSTALLATION

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

10.CHECK REAR SPEED SENSOR AND SENSOR ROTOR

NG

10.CHECK REAR SPEED SENSOR AND SENSOR ROTOR
a.

Remove the rear speed sensor and the component with the speed sensor rotor.

for Speed Sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for 4WD/AWD)>REMOVAL

for Speed Sensor Rotor: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor tip and speed sensor rotor.

OK:

The sensor tip and rotor are free of scratches, oil, and foreign matter.


NOTICE:
·

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.




Result:
Proceed to
OK
NG



OK

11.INSPECT PARKING BRAKE WIRE ASSEMBLY

NG

CLEAN OR REPLACE REAR SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

11.INSPECT PARKING BRAKE WIRE ASSEMBLY
a.
C405858C01
0.823,0.427 1.125,0.677 0.302,0.25 0.823,0.75 1.125,1 0.302,0.25 2.323,0.406 2.688,0.656 0.365,0.25 2.333,0.708 2.677,0.958 0.344,0.25 0.469,2.479 0.844,1.906 true 1.458,2.521 1.083,1.896 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *1 0.844,0.479 1.156,0.677 0.313,0.198 10 false M50 0.854,0.792 1.167,0.99 0.313,0.198 10 false N58 1.219,0.479 1.531,0.677 0.313,0.198 10 false *A 1.219,0.792 1.531,0.99 0.313,0.198 10 false *B 2.365,0.458 2.75,0.635 0.385,0.177 10 false MM2 2.365,0.76 2.729,0.958 0.365,0.198 10 false NN2 2.75,0.771 3.063,0.969 0.313,0.198 10 false *B 2.76,0.458 3.073,0.656 0.313,0.198 10 false *A 0.302,2.5 0.625,2.719 0.323,0.219 10 false RA- 1.458,2.573 1.823,2.802 0.365,0.229 10 false RA+ 0.906,1.104 1.219,1.302 0.313,0.198 10 false *a 2.438,1.094 2.75,1.292 0.313,0.198 10 false *b 0.302,2.75 0.625,2.969 0.323,0.219 10 false LA- 1.458,2.792 1.823,3.021 0.365,0.229 10 false LA+ 1.771,2.594 2.083,2.792 0.313,0.198 10 false *A 0.604,2.521 0.917,2.719 0.313,0.198 10 false *A 0.594,2.771 0.906,2.969 0.313,0.198 10 false *B 1.75,2.823 2.063,3.021 0.313,0.198 10 false *B
*A for RH
*B for LH
*1 Skid Control Sensor Wire (Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the M50 or N58 skid control sensor wire (parking brake wire assembly) connector.


c.

Disconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
M50-2 (RA+) - MM2-3 Always Below 1 Ω
M50-2 (RA+) or MM2-3 - Body ground and other terminals Always 10 kΩ or higher
M50-1 (RA-) - MM2-4 Always Below 1 Ω
M50-1 (RA-) or MM2-4 - Body ground and other terminals Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
N58-2 (LA+) - NN2-3 Always Below 1 Ω
N58-2 (LA+) or NN2-3 - Body ground and other terminals Always 10 kΩ or higher
N58-1 (LA-) - NN2-4 Always Below 1 Ω
N58-1 (LA-) or NN2-4 - Body ground and other terminals Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR SPEED SENSOR)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - REAR SPEED SENSOR)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Reconnect the MM2 or NN2 skid control sensor wire (parking brake wire assembly) connector.


c.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A42-22 (RR+) - M50-2 (RA+) Always Below 1 Ω
A42-22 (RR+) or M50-2 (RA+) - Body ground Always 10 kΩ or higher
A42-9 (RR-) - M50-1 (RA-) Always Below 1 Ω
A42-9 (RR-) or M50-1 (RA-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A42-20 (RL+) - N58-2 (LA+) Always Below 1 Ω
A42-20 (RL+) or N58-2 (LA+) - Body ground Always 10 kΩ or higher
A42-7 (RL-) - N58-1 (LA-) Always Below 1 Ω
A42-7 (RL-) or N58-1 (LA-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C233859C92
0.646,0.521 1.135,0.813 0.49,0.292 2,0.521 2.49,0.813 0.49,0.292 0.969,1.344 1.177,1.781 true 2.323,1.344 2.531,1.781 true 1.188,1.813 1.583,2.052 0.396,0.24 10 false RA+ 2.552,1.823 2.979,2.031 0.427,0.208 10 false LA+ 0.135,0.083 0.323,0.24 0.188,0.156 10 false *a 0.76,0.594 1.052,0.75 0.292,0.156 10 false M50 2.125,0.594 2.573,0.792 0.448,0.198 10 false N58 0.427,0.583 0.74,0.781 0.313,0.198 10 false *A 1.771,0.573 2.083,0.771 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
M50-2 (RA+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
N58-2 (LA+) - Body ground Power switch on (IG) 5.7 to 14 V



Result:
Proceed to
OK
NG



OK

NG