Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat) › 2019.02–2020.08
RM3620E _58 Vehicle Interior _076405 SEAT _0372017 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Position control ECU assembly (driver seat) (Including removal and installation)

·

Reclining motor (Front seatback frame sub-assembly (driver seat)) (Including removal and installation)

·

Slide motor (Front seat adjuster assembly (driver seat)) (Including removal and installation)

·

Power seat lifter motor assembly (driver seat) (Including removal and installation)

·

Lumbar support adjuster assembly (driver seat) (Including removal and installation)

·

Power seat tilt motor assembly (driver seat) (Including removal and installation)


Initialize position control ECU Front power seat control system (for HV model with memory) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Position control ECU assembly (driver seat) (Including removal and installation)

·

Reclining motor (Front seatback frame sub-assembly (driver seat)) (Including removal and installation)

·

Slide motor (Front seat adjuster assembly (driver seat)) (Including removal and installation)

·

Power seat lifter motor assembly (driver seat) (Including removal and installation)

·

Lumbar support adjuster assembly (driver seat) (Including removal and installation)

·

Power seat tilt motor assembly (driver seat) (Including removal and installation)


Initialize position control ECU Front power seat control system (for Gasoline model with memory) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


CAUTION:
·
B521791

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



NOTICE:
·

If the front seat airbag assembly was deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

·

Replace any other damaged parts as necessary.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 71910A 5.REMOVE FRONT SEAT HEADREST ASSEMBLY

a.

Remove the front seat headrest assembly from the front seat assembly LH.


Hide 72124 6.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH

a.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.


b.
B521460C02
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V100155

Protective Tape


Using a thin-bladed screwdriver, detach the claw.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.

Place your hands at the position shown in the illustration and slide in the removal direction (2) while pulling in the removal direction (1) to detach the guide and remove the front outer seat track bracket cover LH.


Hide 72124A 7.REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH

HINT:

Use the same procedure described for the front outer seat track bracket cover LH.


Hide 72138N 8.REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH

a.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the frontmost position.


b.
B521462C02
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver, detach the claw.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.

Pull in the removal direction shown in the illustration to detach the guide and remove the rear outer seat track bracket cover LH.


Hide 72158E 9.REMOVE REAR INNER SEAT TRACK BRACKET COVER LH

a.
B521464C02
0,0 0,0 false
V113147

Remove in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver, detach the claw.

HINT:

Tape the thin-bladed screwdriver tip before use.



b.

Pull in the removal direction shown in the illustration to detach the guide and remove the rear inner seat track bracket cover LH.


Hide 10.REMOVE FRONT SEAT ASSEMBLY LH

a.
B526555

Using a T50 "TORX" socket wrench, remove the 2 "TORX" screws.


b.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.


c.
B526554

Using a T50 "TORX" socket wrench, remove the 2 "TORX" screws.


d.

Operate the reclining power seat switch knob and move the seatback of the front seat assembly LH perpendicular.


e.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the center position.


f.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the uppermost position.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.


iv.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




h.

Tilt the front seat assembly LH backward.

NOTICE:

Be careful not to damage the front seat assembly LH or interior parts.



i.
B526558C01
1.573,0.604 2.344,0.156 2.344,0.156 2.938,0.156 true 2.969,0.052 3.281,0.208 0.313,0.156 10 false *a
*a Front Seat Airbag Assembly LH Connector


Disconnect the front seat airbag assembly LH connector.

i.

Push down the white housing lock and slide the yellow CPA in the slide direction (1) as shown in the illustration.

B517372C06
1.76,1.271 2.292,0.958 true 3.552,1.271 4.083,0.958 true 3.354,2.406 3.531,1.688 true 1.49,2.417 1.667,1.698 true 0.771,1.385 1.469,1.396 true 2.333,0.844 2.646,1.042 0.313,0.198 10 false *a 4.094,0.833 4.406,1.031 0.313,0.198 10 false *a 3.281,2.438 3.594,2.635 0.313,0.198 10 false *b 1.427,2.438 1.74,2.635 0.313,0.198 10 false *b 0.563,1.313 0.875,1.51 0.313,0.198 10 false (A)
*a Housing Lock *b Yellow CPA
V113147

Slide in this Direction (1)
V113148

Slide in this Direction (2)


NOTICE:
·

Do not pull while holding the wire harness.

·

Do not try to release the lock while holding down the top of the yellow CPA (A in the illustration), as this prevents the lock from being released.




ii.

Slide the yellow CPA in the slide direction (2) while pushing down the white housing lock again, and disconnect the connector.



j.

Disconnect the other 2 connectors under the front seat assembly LH.


k.

Detach the clamp.


l.
B526556

Remove the front seat assembly LH as shown in the illustration.

NOTICE:
·

2 or more people are required when carrying the front seat assembly LH out of the vehicle.

·

Protect the front seat legs.

·

Be careful not to damage the front seat assembly LH, body exterior or interior parts.