Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › from 2019.02
RM3620E _58 Vehicle Interior _076406 SEAT BELT _0377520 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSPECT FRONT SEAT OUTER BELT ASSEMBLY

Hide 73024 2.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

a.
B521511

Attach the guide to install the front shoulder belt anchor plate sub-assembly LH.


Hide 73200A 3.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B521437N01
2.177,1.938 2.427,2.156 0.25,0.219 10 true (1) 2.198,0.365 2.448,0.583 0.25,0.219 10 true (2)

Attach the guide and temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73220 4.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B521436

Attach the guide.


b.

Install the front seat outer belt assembly LH with the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.
B521433C01
2.771,1 2.25,0.594 true 2.063,0.417 2.375,0.573 0.313,0.156 10 false *a
*a Locking Button
V113147

Install in this Direction


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:
·

When handling the pretensioner connector, take care not to damage the pretensioner wire harness.

·

Securely lock the locking button.




d.
B521431

Install the shoulder anchor of the front seat outer belt assembly LH with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62412 5.INSTALL CENTER PILLAR GARNISH LH

Hide 62414A 6.INSTALL LOWER CENTER PILLAR GARNISH LH

Hide 73220 7.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

a.
B521430

Install the anchor of the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Check that the ELR locks.

With the front seat outer belt assembly LH installed to the vehicle, check that the belt locks when it is pulled out quickly.


Hide 73233 8.INSTALL LAP BELT OUTER ANCHOR COVER

a.
B521429

Attach the guide and claw to install the lap belt outer anchor cover.


Hide 62312B 9.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67914B 10.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 62332C 11.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67918E 12.INSTALL REAR DOOR SCUFF PLATE LH

Hide 72693 13.INSTALL REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)

Hide 14.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)

Hide 15.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 16.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 17.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 18.INSTALL DECK BOARD ASSEMBLY (for HV Model)