Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY (for NICKEL METAL HYDRIDE BATTERY) › 2020.05–2020.08
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0371642 HV RELAY ASSEMBLY(for NICKEL METAL HYDRIDE BATTERY) A

HYBRID / BATTERY CONTROL  HV RELAY ASSEMBLY(for NICKEL METAL HYDRIDE BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery junction block assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.


·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 82111 3.DISCONNECT ENGINE ROOM MAIN WIRE

Hide 82111 7.CONNECT ENGINE ROOM MAIN WIRE

Hide 8.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 9.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 899A0 10.REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Hide 67918E 11.REMOVE REAR DOOR SCUFF PLATE LH

Hide 58467H 12.REMOVE NO. 3 BATTERY SERVICE COVER BOARD

Hide 67917C 13.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 58466J 14.REMOVE NO. 2 BATTERY SERVICE COVER BOARD

Hide 58464D 15.REMOVE BATTERY SERVICE COVER BOARD

Hide 71033 16.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide 82161 19.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A430955C01
2.385,0.063 2.698,0.26 0.313,0.198 10 true *a 0.563,1.74 0.875,1.938 0.313,0.198 10 true *b
*a Electric Vehicle Battery Plug Assembly Connector
*b HV Battery Junction Block Assembly Connector


Disengage the clamp.


b.

Disconnect the electric vehicle battery plug assembly connector.


c.

Disconnect the HV battery junction block assembly connector.


d.
A430956

Disengage the 2 clamps to disconnect the floor wire.


Hide G92Z0 22.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A431941

Remove the bolt and disconnect the electric vehicle battery plug assembly.


b.
A431942

Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected connectors with insulating tape.



c.

Disengage the clamp.


d.
A431943

Disengage the 2 claws and open the wiring harness protector.


e.
A431944

Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected connectors with insulating tape.



f.
A431945C01
2.333,2.531 2.583,2.531 true 2.604,2.448 2.833,2.656 0.229,0.208 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the wiring harness protector.


g.
A431946

Disconnect the HV battery junction block assembly connector.


h.
A431947

Remove the 4 nuts and HV battery junction block assembly from the HV battery.

NOTICE:

If the HV battery junction block assembly has been struck or dropped, replace it with a new one.