Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER (for HV Model 4WD/AWD) › from 2020.05
RM3620E _53 Suspension _076491 REAR SUSPENSION _0389149 REAR SUSPENSION MEMBER(for HV Model 4WD/AWD) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for HV Model 4WD/AWD)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.
C410661N01
1.063,0.427 1.219,0.625 0.156,0.198 10 false A 1.906,0.146 2.063,0.344 0.156,0.198 10 false A 2.333,0.833 2.49,1.031 0.156,0.198 10 false A 3.25,0.906 3.406,1.104 0.156,0.198 10 false A 0.667,1.458 0.823,1.656 0.156,0.198 10 false B 0.26,1.063 0.417,1.26 0.156,0.198 10 false B

Install the 6 hole plugs to the rear suspension member sub-assembly.

HINT:

There are 2 different shapes of hole plug.



Hide 41651G 2.INSTALL DIFFERENTIAL MOUNT CUSHION

a.

Using SST, install a new differential mount cushion.

SST
09316-12010  
09570-24011  

C413724C01
5.51,3.333 5.76,3.333 5.76,3.333 5.76,3 false 5.698,3.333 5.698,3.083 false 6.104,3.354 5.938,3.354 5.938,3.354 5.854,3.188 false 5.854,0.74 6.438,0.823 6.438,0.823 5.865,0.615 true 6.146,3.292 6.563,3.625 0.417,0.333 10 false *1 5.771,0.292 6.104,0.542 0.333,0.25 10 false *a 5.729,1.75 6.063,2 0.333,0.25 10 false *b 6.479,0.75 6.813,1 0.333,0.25 10 false *c 2.313,1.365 2.625,1.521 0.313,0.156 10 false *d 3.75,1.208 4.063,1.365 0.313,0.156 10 false *e 5.219,3.281 5.635,3.531 0.417,0.25 10 false SST
*1 Rear Suspension Member Sub-assembly - -
*a -3° to 3° *b 3.1 to 4.1 mm (0.1220 to 0.1614 in.)
*c Protrusion *d Turn
*e Hold - -
V100135

Turning Direction
V100136

Front of Vehicle
V100137

SST Bolt Position - -


NOTICE:
·

Make sure that the differential mount cushion is aligned within 3° from the center.

·

Install the differential mount cushion so that the protrusion is positioned as shown in the illustration.

·

Be sure to use the correct combination of SST.

·

Before using SST, apply grease to SST bolt.

·

Temporarily install the differential mount cushion to the rear suspension member sub-assembly in order to prevent it from tilting, and then install SST.

·

Make sure that SST contacts the entire circumference of the differential mount cushion.

·

Do not tilt the bolts of SST.




Hide 52271D 3.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

Hide 52271D 4.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

Hide 52276A 5.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH

Hide 52275B 6.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH

Hide 48790 7.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 8.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide G1050 9.INSTALL REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

Hide 51206A 11.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.

Install the 4 rear suspension member cushions to the rear suspension member sub-assembly.

HINT:

When reusing the rear suspension member cushion, make sure to check its identification mark and install it to the correct position.



b.
C410660C02
2.75,4.146 2.75,3.979 2.75,3.979 2.917,3.979 false 2.021,4.125 2.021,3.958 2.021,3.958 2.188,3.958 false 0.948,4.135 0.865,3.969 0.865,3.969 1.448,4.052 true 0.396,4.25 0.396,4.083 0.396,4.083 0.563,4.083 false 0.604,4.021 0.938,4.271 0.333,0.25 10 false *a 2.958,3.917 3.208,4.167 0.25,0.25 10 false *b 2.229,3.896 2.479,4.146 0.25,0.25 10 false *b 0.698,3.885 0.948,4.135 0.25,0.25 10 false *b 0.094,0.521 0.25,0.719 0.156,0.198 10 true A 3.115,0.625 3.271,0.823 0.156,0.198 10 true A 0.146,1.917 0.302,2.115 0.156,0.198 10 true B 3.104,1.927 3.26,2.125 0.156,0.198 10 true B 2.25,2.104 2.406,2.302 0.156,0.198 10 true C 1.042,2.104 1.198,2.302 0.156,0.198 10 true C
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
C410424

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:
·

Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.

·

Keep supporting the rear suspension member sub-assembly until the installation has been completed.




c.

Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.


d.

Install the rear suspension member sub-assembly with the 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH, 2 bolts and 4 nuts.

Torque:
Bolt A : 158 N*m (1611 kgf*cm, 117 ft.*lbf)
Nut B : 158 N*m (1611 kgf*cm, 117 ft.*lbf)
Nut C : 18 N*m (184 kgf*cm, 13 ft.*lbf)


e.

Engage the 5 clamps to install the wire harness.


f.

Pass the connector through the hole to the inside of the vehicle and install the grommet of the wire harness.


g.

Connect the 2 connectors.


Hide 821H1 12.INSTALL HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A445300C01
2.594,3.104 2.208,3.104 2.208,3.104 1.896,2.667 true 2.646,3 2.958,3.198 0.313,0.198 10 false *a
*a Waterproof Seal


Install the HV floor under wire to the rear traction motor with transaxle assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

Make sure that the connector is fully engaged.

·

Do not damage the terminals, interlock connector or rear traction motor with transaxle assembly during installation.

·

Do not touch the waterproof seal or terminals of the connector.

·

Do not allow any foreign matter or water to enter the rear traction motor with transaxle assembly.

·

Although the connector may feel loose, this is not due to a malfunction.




b.
A435162

Engage the clamp.


Hide 48720A 13.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.

Temporarily install the rear No. 1 suspension arm assembly to the rear suspension member sub-assembly with the bolt and nut.

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Insert the bolt with the threaded end facing the rear of the vehicle.




Hide 48710A 14.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 15.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 16.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 18.INSTALL REAR DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 19.INSTALL REAR STABILIZER BAR

Hide 64740E 20.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 58460D 21.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

Hide 73708A 22.INSTALL TETHER ANCHOR BRACKET SET

Hide 62552F 23.INSTALL REAR SEAT SIDE GARNISH LH

Hide 62332C 24.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67918E 25.INSTALL REAR DOOR SCUFF PLATE LH

Hide 58577E 26.INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE

Hide 58386 27.INSTALL REAR FLOOR FINISH PLATE

Hide 58417H 28.INSTALL REAR NO. 3 FLOOR BOARD

Hide 64993 29.INSTALL REAR DECK FLOOR BOX (w/o Spare Tire)

Hide 58410B 30.INSTALL DECK BOARD ASSEMBLY

Hide 64910N 31.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 73706 32.INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH

Hide 33.INSTALL REAR SEAT ASSEMBLY

Hide 48720A 35.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 36.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 58398F 37.INSTALL NO. 1 FLOOR UNDER COVER (w/ NO. 1 FLOOR UNDER COVER)

a.

Install the No. 1 floor under cover to the rear suspension member sub-assembly with the 3 bolts and 3 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 39.INSTALL REAR WHEEL

Hide 40.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 41.PERFORM INITIALIZATION

Parking Support Brake System (for HV model) (Click here)
Parking Assist Monitor System (Click here)
Panoramic View Monitor System (for HV model) (Click here)
Lighting System (EXT) (Click here)