This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
25861A
1.INSTALL NO. 2 VACUUM SWITCHING VALVE BRACKET
Using an 8 mm socket wrench, install the No. 2 vacuum switching valve bracket to the cylinder head sub-assembly with the 2 bolts.
2.INSTALL PURGE VALVE (PURGE VSV)
w/ Canister Pump Module:
Click hereEngine / Hybrid System>A25A-FKS (EMISSION CONTROL)>PURGE VALVE(w/ Canister Pump Module)>INSTALLATION
w/o Canister Pump Module:
17169A
3.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the 2 bolts.
11452
4.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the engine oil level dipstick guide.
Using an 8 mm socket wrench, install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.
Install the engine oil level dipstick.
19500
5.INSTALL IGNITION COIL ASSEMBLY
23255A
6.INSTALL FUEL INJECTOR SEAL
23250E
7.INSTALL DIRECT FUEL INJECTOR ASSEMBLY
23814B
8.INSTALL FUEL DELIVERY PIPE
23250F
9.INSTALL PORT FUEL INJECTOR ASSEMBLY
82125N
10.INSTALL NO. 5 ENGINE WIRE
23291
11.INSTALL INJECTOR VIBRATION INSULATOR
23807V
12.INSTALL NO. 1 DELIVERY PIPE SPACER
23807
13.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
14.INSTALL WIRE HARNESS CLAMP BRACKET
Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.
82126A
15.INSTALL NO. 6 ENGINE WIRE
Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.
Attach the 2 clamps.
Connect the 4 connectors.
82219A
16.INSTALL SENSOR WIRE
Using an 8 mm socket wrench, install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.
Attach the 3 clamps.
Connect the 4 connectors.
16295
17.INSTALL NO. 7 WATER BY-PASS HOSE
Install the No. 7 water by-pass hose and slide the 2 clips to secure it.
23100X
18.TEMPORARILY INSTALL FUEL PUMP ASSEMBLY (for High Pressure)
23801P
19.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
23100X
20.INSTALL FUEL PUMP ASSEMBLY (for High Pressure)
23801P
21.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
| *a | 17 mm Union Nut Wrench |
| *b | Torque Wrench Fulcrum Length |
Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
23901
22.CONNECT FUEL TUBE SUB-ASSEMBLY
17177
23.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
17111
24.INSTALL INTAKE MANIFOLD
16278
25.INSTALL NO. 2 WATER BY-PASS PIPE
Install the bolt (A).
Using an 8 mm socket wrench, install the No. 2 water by-pass pipe with the 2 bolts (B) in the order shown in the illustration.
16279
26.INSTALL NO. 3 WATER BY-PASS PIPE
Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.
Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.
25620
27.INSTALL EGR VALVE ASSEMBLY
Using an 8 mm socket wrench, install the EGR valve bracket with the bolt.
| *a | Pin |
| *b | Hole |
Align and fit the hole of the EGR valve bracket to the pin of the camshaft housing sub-assembly.
Using an 8 mm socket wrench, install the EGR valve assembly with the 2 bolts.
Connect the No. 8 water by-pass hose to the EGR valve assembly and slide the clip to secure it.
Connect the clamp.
28.INSTALL NO. 4 WATER BY-PASS HOSE
Connect the No. 4 water by-pass hose to the EGR valve assembly and slide the clip to secure it.
25601
29.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
Using an 8 mm socket wrench, install the No. 1 EGR pipe sub-assembly, a new EGR inlet gasket and a new EGR valve adapter gasket with the 4 bolts.
25687
30.INSTALL NO. 1 EGR COOLER BRACKET
Install the No. 1 EGR cooler bracket to the EGR valve bracket and water outlet with the 2 bolts.
25680
31.INSTALL EGR COOLER ASSEMBLY
Install the EGR cooler assembly, a new EGR cooler gasket and a new EGR valve gasket with the 5 bolts.
Connect the No. 3 water by-pass hose to the EGR cooler assembly and slide the clip to secure it.
Connect the water hose to the EGR cooler assembly and slide the clip to secure it.
22030
32.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
17141
33.INSTALL EXHAUST MANIFOLD
17118
34.INSTALL MANIFOLD STAY
17167
35.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 5 bolts.
16260
36.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)
| *a | View A |
| *b | 90° |
| *c | Upper Side |
| *d | RH Side |
| *e | 2 to 7 mm (0.0787 to 0.276 in.) |
Connect the flow shutting valve (water by-pass hose assembly) to the water by-pass outlet sub-assembly and slide the clip to secure it.
Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the water by-pass outlet sub-assembly.
Make sure that the claws of the clip are within the location shown in the illustration.
Install the water hose clamp bracket with the 2 bolts.
Connect the flow shutting valve (water by-pass hose assembly) with the bolt.
16207
37.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Connect the No. 2 water by-pass pipe sub-assembly with the bolt.
Connect the No. 2 water by-pass pipe sub-assembly to the outlet water by-pass sub-assembly and slide the clip to secure it.
11323C
38.INSTALL NO. 3 TIMING CHAIN COVER
Using an 8 mm socket wrench, install the No. 3 timing chain cover and plate washer to the No. 2 timing chain cover assembly with the bolt.
11336A
39.INSTALL TIMING GEAR COVER INSULATOR
Using an 8 mm socket wrench, install the timing gear cover insulator and plate washer to the No. 2 timing chain cover assembly with the bolt.
11336A
40.INSTALL NO. 2 TIMING CHAIN COVER INSULATOR
Install the No. 2 timing chain cover insulator to the V-ribbed belt tensioner assembly.
16620D
41.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.
Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.
Install the V-ribbed belt tensioner assembly to the No. 2 timing chain cover assembly with the 2 bolts.
12602C
42.INSTALL NO. 2 ENGINE COVER
Install the No. 2 engine cover to the No. 2 timing chain cover assembly with the 2 bolts.
88310
43.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY
for Type A:
Using an E8 "TORX" socket wrench, temporarily install the compressor assembly with pulley with the 2 stud bolts.
|
Bolt |
|
Nut |
Install the compressor assembly with pulley with the 2 bolts and 2 nuts.
Tighten the bolts and nuts in the order shown in the illustration.
for Type B:
Install the compressor assembly with pulley with the 4 bolts.
Tighten the bolts in the order shown in the illustration.
27020
44.INSTALL GENERATOR ASSEMBLY
for 100 A, 130 A Type:
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 100 A, 130 A Type)>INSTALLATION
for 150 A Type:
Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>GENERATOR(for 150 A Type)>INSTALLATION
16361A
45.INSTALL V-RIBBED BELT
43457
46.INSTALL DRIVE SHAFT BEARING BRACKET
Install the drive shaft bearing bracket with the 3 bolts.