Home › Power Source / Network › NETWORKING › NETWORK GATEWAY ECU (for LHD) › from 2020.08
RM3620E _57 Power Source / Network _076016 NETWORKING _0371088 NETWORK GATEWAY ECU(for LHD) A

NETWORKING  NETWORK GATEWAY ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the network gateway ECU removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION (for Manual Transaxle)

CAUTION:
B475753

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58810J 6.REMOVE CONSOLE BOX ASSEMBLY

Hide 67913B 7.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111C 8.REMOVE COWL SIDE TRIM BOARD RH

Hide 55607 9.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55550 10.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55433B 11.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 82877 12.REMOVE ECU INTEGRATION BOX RH (except Manual Transaxle)

a.
E405568

w/ Clearance Warning System:

i.

Disconnect the connector.



b.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and relay holder.

E405569C01
0.438,0.385 0.698,0.594 0.26,0.208 12 true *A
*A Relay holder reverse side - -
V100155

Protective Tape - -



c.
E405570

Disconnect the 4 connectors.


d.

Detach the 3 wire harness clamps.


e.
E405571C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Remove the nut, bolt and ECU integration box RH.


Hide 13.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Manual Transaxle)

Hide 82877 14.REMOVE ECU INTEGRATION BOX RH (for Manual Transaxle)

a.
E405574C01
2.5,1.427 2.771,1.625 0.271,0.198 10 true *a
*a w/ Clearance Warning System


Detach the wire harness clamp.


b.

w/ Clearance Warning System:

i.

Disconnect the 5 connectors.



c.

w/o Clearance Warning System:

i.

Disconnect the 4 connectors.



d.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and wire harness protector and remove ECU integration box RH.

E405573C01
0.427,0.385 0.698,0.604 0.271,0.219 12 true *A
*A Harness protector reverse side - -
V100155

Protective Tape - -



Hide 89111 15.REMOVE NETWORK GATEWAY ECU

a.
E403047C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the network gateway ECU.