The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
64910N
2.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
58410B
3.REMOVE DECK BOARD ASSEMBLY
58416K
4.REMOVE REAR NO. 2 FLOOR BOARD
58417H
5.REMOVE REAR NO. 3 FLOOR BOARD
64993
6.REMOVE REAR DECK FLOOR BOX (w/o Spare Tire)
58386
7.REMOVE REAR FLOOR FINISH PLATE
65351A
8.REMOVE BATTERY HOLE COVER (for HV Model)
9.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
for A25B-FXS:
Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
10.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
11.REMOVE REAR SEAT CUSHION LOCK HOOK
12.REMOVE REAR SEATBACK ASSEMBLY LH
73350C
13.REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)
14.REMOVE REAR SEATBACK ASSEMBLY RH
71304C
15.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH
71303C
16.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
73706
17.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
73705
18.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
67918E
19.REMOVE REAR DOOR SCUFF PLATE LH
67917C
20.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
58467H
21.REMOVE NO. 3 BATTERY SERVICE COVER BOARD (for HV Model)
58466J
22.REMOVE NO. 2 BATTERY SERVICE COVER BOARD (for HV Model)
58464D
23.REMOVE BATTERY SERVICE COVER BOARD (for HV Model)
58577E
24.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
62332C
25.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Pull back the rear door opening trim weatherstrip LH so that the deck trim side panel assembly LH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP>REMOVAL
62331C
26.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
Pull back the rear door opening trim weatherstrip RH so that the deck trim side panel assembly RH can be removed.
62552F
27.REMOVE REAR SEAT SIDE GARNISH LH
62551F
28.REMOVE REAR SEAT SIDE GARNISH RH
Use the same procedure described for the LH side.
73708A
29.REMOVE TETHER ANCHOR BRACKET SET
58460D
30.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
64740E
31.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
64730J
32.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
62480A
33.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH
62470A
34.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH
Use the same procedure described for the LH side.
73370E
35.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH
Remove the bolt and the floor anchor of the rear seat outer belt assembly LH.
w/ Pretensioner and Force Limiter:
| *a | Locking Button |
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
|
Bolt |
|
Nut |
Remove the bolt and nut.
Detach the guide to remove the rear seat outer belt assembly LH.
Remove the bolt.
Detach the guide to remove the rear seat outer belt anchor bracket sub-assembly LH.
73360D
36.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH
Remove the bolt and floor anchor of the rear seat outer belt assembly RH.
w/ Pretensioner and Force Limiter:
| *a | Locking Button |
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
|
Bolt |
|
Nut |
Remove the bolt and nut.
Detach the guide to remove the rear seat outer belt assembly RH.
Remove the bolt.
Detach the guide to remove the rear seat outer belt anchor bracket sub-assembly RH.