Home › Engine / Hybrid System · 2UZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0011    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0012    Camshaft Position "A" - Timing Over-Retarded (Bank 1)

DTC    P0021    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)

DTC    P0022    Camshaft Position "A" - Timing Over-Retarded (Bank 2)

for Preparation Click here


DESCRIPTION

The VVT system includes the ECM, Camshaft Oil Control Valve (OCV) and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A192077E01


DTC No.
DTC Detection Condition
Trouble Area
P0011
P0021
Valve timing is not adjusted in valve timing advance range
(1 trip detection logic)
  1. Valve timing
  2. OCV
  3. OCV filter
  4. Intake camshaft timing tube assembly
  5. ECM
P0012
P0022
Valve timing is not adjusted in valve timing retard range
(2 trip detection logic)
  1. Valve timing
  2. OCV
  3. OCV filter
  4. Intake camshaft timing tube assembly
  5. ECM

MONITOR DESCRIPTION

  1. The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the Camshaft Oil Control Valve (OCV) and the VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
  2. If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores a DTC.
  1. Example:
  2. A DTC is set when the following conditions 1 and 2 are met for 10 seconds or more:
    1. 1. The difference between the target and actual intake valve timings is more than 5°CA (Crankshaft Angle) and the condition continues for more than 5 seconds.
    2. 2. It takes 5 seconds or more to change the valve timing by 5°CA.
  3. DTC P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.
  4. DTC P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.
  5. These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the presence of foreign objects in the OCV.
  6. The monitor will run if all of the following conditions are met:
    1. The engine is warm (the engine coolant temperature is 75°C [167°F] or more).
    2. The vehicle has been driven at more than 64 km/h (40 mph) for 3 minutes.
    3. The engine has idled for 3 minutes.

MONITOR STRATEGY


Related DTCs
P0011: Advanced camshaft timing (bank 1)
P0012: Retarded camshaft timing (bank 1)
P0021: Advanced camshaft timing (bank 2)
P0022: Retarded camshaft timing (bank 2)
Required Sensors/Components (Main)
VVT OCV and VVT Actuator
Required Sensors/Components (Related)
Crankshaft position sensor, Camshaft position sensor and Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
Within 10 seconds
MIL Operation
Advanced camshaft timing: Immediate
Retarded camshaft timing: 2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0016, P0018 (VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
Battery voltage
11 V or more
Engine RPM
400 to 4000 rpm
ECT
75 to 100°C (167 to 212°F)

TYPICAL MALFUNCTION THRESHOLDS


Advanced Camshaft Timing 
Valve timing
No change at advanced valve timing

Retard Camshaft Timing 
Valve timing
No change at retarded valve timing
  1. If the difference between the target and actual camshaft timings is greater than the specified value, the ECM operates the VVT actuator.
  2. Then, the ECM monitors the camshaft timing change for 10 seconds.

WIRING DIAGRAM

Refer to DTC P0010 .

INSPECTION PROCEDURE

HINT:
DTC P0011, P0012, P0021 or P0022 may be set when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain set even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.


HINT:

Abnormal Bank
Advanced Timing Over
(Valve timing is out of specified range)
Retarded Timing Over
(Valve timing is out of specified range)
Bank 1
P0011
P0012
Bank 2
P0021
P0022
  1. If DTC P0011 or P0012 is displayed, check the left bank VVT system circuit (for bank 1).
  2. Bank 1 refers to the bank that includes No. 1 cylinder.
  3. If DTC P0021 or P0022 is displayed, check the right bank VVT system circuit (for bank 2).
  4. Bank 2 refers to the bank that does not include No. 1 cylinder.
  5. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0011, P0012, P0021 or P0022 is output
    A
    P0011, P0012, P0021 or P0022 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream ON.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.

    OK:
    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine speed
    OCV ON
    Engine idles roughly or stalls
    (soon after OCV switched from OFF to ON)



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the Techstream.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs using the Techstream.

    OK:
    No DTC is output.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TOOTH OF TIMING BELT)
A115368E03
  1. Remove the drive belt (Click here).

  1. Remove the timing belt cover LH and RH (Click here).

  1. Turn the crankshaft to align the alignment marks of the crankshaft.

  1. Align the notch of the crankshaft pulley with the "0" position.

  1. Confirm whether the alignment marks of the camshaft pulley and cylinder head cover are facing each other.

  1. If the alignment marks are not facing each other, turn the crankshaft clockwise by 360°. Confirm again if the alignment marks are facing each other.

    OK:
    The alignment marks of the camshaft pulley and the cylinder head cover face each other when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING (Click here)
OK


5.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY (OCV)
A160397E12
A178642E01
  1. Remove the OCV.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. Apply the positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.



NG
REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER
A086178E01
  1. Remove the cylinder head cover for bank 1 (Click here).

  1. Remove the cylinder head cover for bank 2 (Click here).

  1. Remove the camshaft bearing cap and OCV filter.

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


7.REPLACE CAMSHAFT TIMING TUBE ASSEMBLY
  1. Replace the camshaft timing tube assembly (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream ON.

  1. Clear DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the Techstream.

  1. Drive the vehicle for more than 10 minutes.

  1. Read output DTCs using the Techstream.

    OK:
    No DTC is output.

    HINT:
    DTC P0011, P0012, P0021 or P0022 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

END