Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1820/55  Short in Front Driver Side - Side Squib Circuit  B1821/55  Open in Front Driver Side - Side Squib Circuit  B1822/55  Short to GND in Front Driver Side - Side Squib Circuit  B1823/55  Short to B+ in Front Driver Side - Side Squib Circuit  


DESCRIPTION

The side squib LH circuit consists of the center airbag sensor and the front seat side airbag LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib LH circuit.

DTC Code Detection Condition Trouble Area
B1820/55 When one of following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the side squib LH circuit during primary check.

·

Side squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1821/55 When one of following conditions is met:
·

The center airbag sensor receives an open circuit signal in the side squib LH circuit for 2 seconds.

·

Side squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1822/55 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the side squib LH circuit for 0.5 seconds.

·

Side squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1823/55 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the side squib LH circuit for 0.5 seconds.

·

Side squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

U153617E02
2.813,1.563 3.208,1.719 0.396,0.156 10 false SFL+ 2.813,2.406 3.156,2.563 0.344,0.156 10 false SFL- 4.875,1.667 5.313,1.823 0.438,0.156 10 false SFD+ 4.875,2.5 5.281,2.656 0.406,0.156 10 false SFD- 3.313,1.771 3.542,1.958 0.229,0.188 10 false 1 3.313,2.615 3.49,2.802 0.177,0.188 10 false 2 2.552,3 2.823,3.167 0.271,0.167 10 false O6 2.552,3.146 3.521,3.313 0.969,0.167 10 false Side Squib LH 4.531,1.552 4.698,1.792 0.167,0.24 10 false 9 4.469,2.385 4.708,2.615 0.24,0.229 10 false 10 4.854,4.177 5.146,4.323 0.292,0.146 10 false O1 4.854,4.344 6.26,4.51 1.406,0.167 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector is properly connected to the front seat side airbag LH.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the front seat side airbag LH.


e.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.




OK

2.CHECK FRONT SEAT SIDE AIRBAG LH (SEAT AIRBAG WIRE LH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT SIDE AIRBAG LH (SEAT AIRBAG WIRE LH)
a.
U153547E01
0.048,1.19 0.814,1.533 0.766,0.343 10 Seat Airbag Wire LH 1.458,1.19 2.856,1.353 1.399,0.163 10 Center Airbag Sensor 0.193,1.818 2.557,2.142 2.364,0.324 10 Front view of wire harness connector: (to Seat Airbag Wire LH) 2.253,2.675 3.069,2.823 0.817,0.147 10 Connector C 2.84,3.617 3.156,3.787 0.316,0.170 10 SST 2.23,4.003 3.009,4.159 0.779,0.156 10 Color: Black 0.549,2.87 0.840,3.039 0.291,0.170 10 O6 2.291,3.555 2.826,3.703 false 1.835,3.785 2.2,4.086 false 0.647,1.19 0.922,0.715 false 1.22,0.811 1.385,1.006 0.165,0.195 10 C 1.005,0.811 1.170,1.006 0.165,0.195 10 D

Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat side airbag LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1820, B1821, B1822, B1823 or 55 is output A
DTC B1820, B1821, B1822, B1823 or 55 is not output (w/ Manual Seat) B
DTC B1820, B1821, B1822, B1823 or 55 is not output (w/ Power Seat) C

HINT:

Codes other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.




A

3.CHECK CONNECTOR

B

C

3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the connector is properly connected to the center airbag sensor assembly.

OK:

The connector is properly connected.



e.

Disconnect the connector from the center airbag sensor assembly.


f.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



g.

Check that the short spring for the floor wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

4.CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)
a.
U153447E02
1.531,3.813 1.167,4.115 false 1.823,3.802 2.188,4.104 false 0.781,1.219 1.063,0.74 false 1.479,0.156 1.625,0.156 1.625,0.156 1.625,0.573 false 0.479,1.24 1.26,1.552 0.781,0.313 10 false Seat Airbag Wire LH 1.844,1.292 3.198,1.438 1.354,0.146 10 false Center Airbag Sensor 0.563,2.427 2.927,2.802 2.365,0.375 10 false Front view of wire harness connector: (to Seat Airbag Wire LH) 2.25,3.406 3.167,3.635 0.917,0.229 10 false Connector C 0.813,3.458 1.104,3.625 0.292,0.167 10 false O6 1.375,0.813 1.542,1.01 0.167,0.198 10 false C 1.75,0.833 1.917,1.031 0.167,0.198 10 false B 2.156,0.594 2.323,0.792 0.167,0.198 10 false A 1.177,0.813 1.344,1.01 0.167,0.198 10 false D 0.75,0.063 1.469,0.26 0.719,0.198 10 false Floor Wire 0.719,4.146 1.094,4.313 0.375,0.167 10 false SFL+ 2.219,4.146 2.594,4.313 0.375,0.167 10 false SFL-

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O6-1 (SFL+) - Body ground Ignition switch ON Below 1 V
O6-2 (SFL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O6-1 (SFL+) - O6-2 (SFL-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O6-1 (SFL+) - O6-2 (SFL-) Always 1 MΩ or higher
O6-1 (SFL+) - Body ground Always 1 MΩ or higher
O6-2 (SFL-) - Body ground Always 1 MΩ or higher




OK

5.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

5.CHECK CENTER AIRBAG SENSOR
a.
C158868E12
0.896,0.813 0.698,1.51 false 1.552,1.271 2.458,1.594 0.906,0.323 10 false Center Airbag Sensor 0.354,1.531 1.167,1.875 0.813,0.344 10 false Seat Airbag Wire LH 1,0.875 1.146,1.063 0.146,0.188 10 false D 1.125,0.875 1.271,1.063 0.146,0.188 10 false C

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat side airbag LH and the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820, B1821, B1822, B1823 or 55 is not output.


HINT:

Codes other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.




OK

NG