Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825/56  Short in Front Passenger Side - Side Squib Circuit  B1826/56  Open in Front Passenger Side - Side Squib Circuit  B1827/56  Short to GND in Front Passenger Side - Side Squib Circuit  B1828/56  Short to B+ in Front Passenger Side - Side Squib Circuit  


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor and the front seat side airbag RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC Code Detection Condition Trouble Area
B1825/56 When one of following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the side squib RH circuit during primary check.

·

Side squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat side airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1826/56 When one of following conditions is met:
·

The center airbag sensor receives an open circuit signal in the side squib RH circuit for 2 seconds.

·

Side squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat side airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1827/56 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the side squib RH circuit for 0.5 seconds.

·

Side squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat side airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1828/56 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the side squib RH circuit for 0.5 seconds.

·

Side squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat side airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

U153618E01
2.762,1.566 3.158,1.722 0.396,0.156 10 SFR+ 2.797,2.407 3.138,2.562 0.341,0.156 10 SFR- 4.794,1.664 5.231,1.820 0.437,0.156 10 SFP+ 4.794,2.505 5.200,2.660 0.406,0.156 10 SFP- 3.232,1.769 3.457,1.960 0.225,0.191 10 1 3.232,2.617 3.408,2.807 0.177,0.191 10 2 2.475,3.009 2.863,3.172 0.388,0.163 10 P5 *1 2.475,3.177 2.923,3.340 0.448,0.163 10 P16 *2 2.475,3.346 3.442,3.516 0.967,0.170 10 Side Squib RH 4.577,1.552 4.740,1.791 0.163,0.239 10 7 4.563,2.385 4.802,2.611 0.239,0.225 10 6 4.836,4.179 5.124,4.321 0.288,0.142 10 P1 4.836,4.341 6.215,4.511 1.379,0.170 10 Center Airbag Sensor 0.831,4.21 2.072,4.380 1.240,0.170 10 *2: w/o Power Seat 0.831,3.944 2.072,4.114 1.240,0.170 10 *1: w/ Power Seat

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector is properly connected to the front seat side airbag RH.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the front seat side airbag RH.


e.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.




OK

2.CHECK FRONT SEAT SIDE AIRBAG RH (SIDE SQUIB RH)

NG

REPLACE NO. 2 FLOOR WIRE

2.CHECK FRONT SEAT SIDE AIRBAG RH (SIDE SQUIB RH)
U153546E01
0.089,1.487 1.432,1.717 1.343,0.230 10 Seat Airbag Wire RH 1.567,1.184 2.946,1.324 1.379,0.140 10 Center Airbag Sensor 0.291,1.893 2.655,2.226 2.364,0.333 10 Front view of wire harness connector: (to Seat Airbag Wire RH) 2.252,2.771 3.171,2.996 0.920,0.225 10 Connector C 2.901,3.423 3.217,3.593 0.316,0.170 10 SST 2.43,3.915 3.209,4.071 0.779,0.156 10 Color: Black 0.834,3.089 1.010,3.258 0.177,0.170 10 *2 0.421,3.089 0.716,3.258 0.295,0.170 10 P16 0.834,2.728 1.010,2.898 0.177,0.170 10 *1 0.473,2.728 0.767,2.898 0.295,0.170 10 P5 2.352,3.361 2.887,3.509 false 2.035,3.697 2.4,3.998 false 0.653,1.487 0.928,1.012 false 1.231,1.132 1.396,1.327 0.165,0.195 10 C 1.016,1.132 1.181,1.327 0.165,0.195 10 D 0.05,4.214 1.294,4.370 1.244,0.156 10 *2: w/o Power Seat 0.05,3.854 1.294,4.009 1.244,0.156 10 *1: w/ Power Seat

a.

Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat side airbag RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1825, B1826, B1827, B1828 or 56 is output A
DTC B1825, B1826, B1827, B1828 or 56 is not output (w/ Manual Seat) B
DTC B1825, B1826, B1827, B1828 or 56 is not output (w/ Power Seat) C

HINT:

Codes other than DTC B1825, B1826, B1827, B1828 and 56 may be output at this time, but they are not related to this check.




A

3.CHECK CONNECTOR

B

C

3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the connector is properly connected to the center airbag sensor assembly.

OK:

The connector is properly connected.



e.

Disconnect the connector from the center airbag sensor assembly.


f.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



g.

Check that the short spring for the No. 2 floor wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

4.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB RH CIRCUIT)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
U153619E02
1.635,3.344 1.208,3.594 false 1.844,3.354 2.229,3.615 false 0.542,1.51 0.823,1.031 false 1.333,0.188 1.448,0.188 false 1.448,0.198 1.375,0.896 false 0.031,1.594 1.365,1.823 1.333,0.229 10 false Seat Airbag Wire RH 1.76,1.208 2.646,1.521 0.885,0.313 10 false Center Airbag Sensor 0.219,2.031 2.583,2.406 2.365,0.375 10 false Front view of wire harness connector: (to Seat Airbag Wire RH) 2.24,2.771 3.156,3 0.917,0.229 10 false Connector C 1.031,3.146 1.313,3.313 0.281,0.167 10 false *2 0.635,3.198 0.917,3.365 0.281,0.167 10 false P16 1.031,2.823 1.313,2.99 0.281,0.167 10 false *1 0.667,2.854 0.948,3.021 0.281,0.167 10 false P5 1.125,1.125 1.292,1.323 0.167,0.198 10 false C 1.5,1.135 1.667,1.333 0.167,0.198 10 false B 1.875,0.885 2.042,1.083 0.167,0.198 10 false A 0.906,1.125 1.073,1.323 0.167,0.198 10 false D 0.74,3.563 1.156,3.729 0.417,0.167 10 false SFP+ 2.26,3.583 2.677,3.75 0.417,0.167 10 false SFR- 0.313,0.094 1.323,0.25 1.01,0.156 10 false No. 2 Floor wire 1.833,4.219 3.073,4.396 1.24,0.177 10 false *2: w/o Power Seat 1.833,3.854 3.042,4.031 1.208,0.177 10 false *1: w/ Power Seat

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Power Seat
Tester Connection Switch Condition Specified Condition
P5-1 (SFR+) - Body ground Ignition switch ON Below 1 V
P5-2 (SFR-) - Body ground Ignition switch ON Below 1 V

w/o Power Seat
Tester Connection Switch Condition Specified Condition
P16-1 (SFR+) - Body ground Ignition switch ON Below 1 V
P16-2 (SFR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Power Seat
Tester Connection Condition Specified Condition
P5-1 (SFR+) - P5-2 (SFR-) Always Below 1 Ω

w/o Power seat
Tester Connection Condition Specified Condition
P16-1 (SFR+) - P16-2 (SFR-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Power Seat
Tester Connection Condition Specified Condition
P5-1 (SFR+) - P5-2 (SFR-) Always 1 MΩ or higher
P5-1 (SFR+) - Body ground Always 1 MΩ or higher
P5-2 (SFR-) - Body ground Always 1 MΩ or higher

w/o Power Seat
Tester Connection Condition Specified Condition
P16-1 (SFR+) - P16-2 (SFR-) Always 1 MΩ or higher
P16-1 (SFR+) - Body ground Always 1 MΩ or higher
P16-2 (SFR-) - Body ground Always 1 MΩ or higher




OK

5.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK CENTER AIRBAG SENSOR
C146261E57
0.823,1.094 0.448,1.479 false 0.104,1.479 1.229,1.813 1.125,0.333 10 false Side Squib RH 0.958,1.198 1.083,1.396 0.125,0.198 10 false D 1.104,1.198 1.25,1.385 0.146,0.188 10 false C 1.552,1.292 2.917,1.458 1.365,0.167 10 false Center Airbag Sensor

a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat side airbag RH and the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825, B1826, B1827, B1828 or 56 is not output.


HINT:

Codes other than DTC B1825, B1826, B1827, B1828 and 56 may be output at this time, but they are not related to this check.




OK

NG