Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.10
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  P2197  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)  P2198  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)  


DESCRIPTION

The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.

The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.

A306366E20
1.49,2.167 1,1.75 1,1.75 0.833,1.75 false 1.656,2.094 1.823,1.844 1.823,1.844 1.906,1.844 false 2.938,1.177 3.104,0.396 3.104,0.396 3.188,0.396 false 3.052,1.198 3.219,0.917 3.219,0.917 3.302,0.917 false 3.156,1.469 3.354,1.198 3.354,1.198 3.5,1.198 false 2.875,1.667 3.406,1.5 3.406,1.5 2.99,1.667 false 3.042,1.75 3.417,2.083 3.417,2.083 3.5,2.083 false 0.281,1.656 1.354,1.854 1.073,0.198 10 false Element 0.135,2.385 1.208,2.583 1.073,0.198 10 false Exhaust Gas 1.083,2.49 1.417,2.667 0.333,0.177 10 false A 1.802,2.49 2.135,2.667 0.333,0.177 10 false A 1.948,1.76 2.333,1.917 0.385,0.156 10 false Cover 3.26,0.219 4.417,0.583 1.156,0.365 10 false Solid Electrolyte (Zirconia Element) 3.365,0.833 4.031,0.99 0.667,0.156 10 false Alumina 3.542,1.104 4.208,1.26 0.667,0.156 10 false Heater 3.448,1.417 4.698,1.667 1.25,0.25 10 false Platinum Electrode 3.542,2 4.688,2.198 1.146,0.198 10 false Atmospheric Air 2.531,2.333 3.865,2.5 1.333,0.167 10 false A-A Cross Section 5.073,0.063 6.948,0.396 1.875,0.333 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 5.563,2.25 6.896,2.417 1.333,0.167 10 false Air Fuel Ratio

DTC Code DTC Detection Condition Trouble Area
P2195
P2197
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is higher than 3.8 V.
(b) Heated oxygen sensor voltage is 0.21 V or higher.
·

Open or short in A/F sensor (for Sensor 1) circuit

·

A/F sensor (for Sensor 1)

·

A/F sensor heater (for Sensor 1)

·

Integration relay

·

A/F sensor heater and integration relay circuits

·

Air induction system

·

Fuel pressure

·

Injector

·

ECM


While fuel-cut operation performed (during vehicle deceleration), A/F sensor current 2.2 mA or more for 3 seconds (2 trip detection logic)
·

A/F sensor

·

ECM


P2196
P2198
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is below 2.8 V.
(b) Heated oxygen sensor voltage is below 0.66 V.
·

Open or short in A/F sensor (for Sensor 1) circuit

·

A/F sensor (for Sensor 1)

·

A/F sensor heater (for Sensor 1)

·

Integration relay

·

A/F sensor heater and integration relay circuits

·

Air induction system

·

Fuel pressure

·

Injector

·

ECM


While fuel-cut operation performed (during vehicle deceleration), A/F sensor current less than 0.7 mA for 3 seconds (2 trip detection logic)
·

A/F sensor

·

ECM



HINT:
·

DTCs P2195 and P2196 indicate malfunctions related to bank 1 A/F sensor circuit.

·

DTCs P2197 and P2198 indicate malfunctions related to bank 2 A/F sensor circuit.

·

Bank 1 refers to the bank that includes No. 1 cylinder.

·

Bank 2 refers to the bank that includes No. 2 cylinder.

·

When either of these DTCs is set, check the A/F sensor output voltage by entering the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS Voltage B1S1 or AFS Voltage B2S1.

·

Short-term fuel trim values can also be read using the Techstream.

·

The ECM regulates the voltages at the A1A+ and A1A- or A2A+ and A2A- terminals of the ECM to a constant level. Therefore, the A/F sensor output voltage cannot be confirmed without using the Techstream.

·

If the A/F sensor is malfunctioning, the ECM sets the DTC P2195, P2196, P2197 or P2198.



MONITOR DESCRIPTION

Sensor voltage detection monitor

Under the air-fuel ratio feedback control, if the A/F sensor output voltage indicates rich or lean for a certain period of time, the ECM determines that there is a malfunction in the A/F sensor. The ECM illuminates the MIL and sets a DTC.

Example:

If the A/F sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds, despite the rear HO2 sensor output voltage being less than 0.66 V, the ECM stores DTC P2196 or P2198. Alternatively, if the A/ F sensor output voltage is more than 3.8 V (very lean condition) for 5 seconds despite the rear HO2 sensor output voltage being 0.21 V or more, DTC P2195 or P2197 is stored.


Sensor current detection monitor

A rich air-fuel mixture causes a low A/F sensor current, and a lean air-fuel mixture causes a high A/F sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the A/F sensor current during fuel-cut and detects any abnormal current values.

If the A/F sensor output is 2.2 mA or more for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the A/F sensor and sets DTC P2195 or P2197 (high-side stuck). If the A/F sensor output is less than 0.7 mA for more than 3 seconds of cumulative time, the ECM sets DTC P2196 or P2198 (low-side stuck).


A107165E70
2.385,2.281 2.219,1.552 2.219,1.552 2.323,1.552 false 4.385,2.281 4.219,1.552 4.219,1.552 4.323,1.552 false 5.771,2.281 5.688,1.573 5.688,1.573 5.771,1.573 false 0.177,0.083 2.073,0.281 1.896,0.198 10 false A/F Sensor Current Monitor: 2.896,0.375 6.646,0.573 3.75,0.198 10 false Cumulative Time "t" = t1 + t2 = 3 seconds or more 0.583,1.073 1.365,1.271 0.781,0.198 10 false Fuel-Cut 1.396,0.927 1.708,1.125 0.313,0.198 10 false ON 1.417,1.229 1.833,1.427 0.417,0.198 10 false OFF 2.406,1.49 3.771,1.688 1.365,0.198 10 false Delay (3 seconds) 4.375,1.458 5.552,1.792 1.177,0.333 10 true Delay (3 seconds) 5.823,1.479 6.99,1.813 1.167,0.333 10 true Delay (3 seconds) 2.354,3.604 3.563,3.927 1.208,0.323 10 true 3 seconds or more 2.313,4.271 4.094,4.469 1.781,0.198 10 false Normal Sensor Output 4.625,4.271 6.292,4.469 1.667,0.198 10 false Abnormal Sensor Output 6.344,4.26 6.813,4.458 0.469,0.198 10 false Time 0.406,2.177 2.052,2.375 1.646,0.198 10 false Sensor Current (mA) 0.396,2.802 1.802,3.031 1.406,0.229 10 false High Side Threshold 0.458,3.448 1.813,3.646 1.354,0.198 10 false Low Side Threshold 4.688,3.698 4.906,3.896 0.219,0.198 10 false t1 6.01,3.698 6.229,3.896 0.219,0.198 10 false t2

MONITOR STRATEGY

Related DTCs P2195: A/F sensor signal stuck lean (Bank 1)
P2196: A/F sensor signal stuck rich (Bank 1)
P2197: A/F sensor signal stuck lean (Bank 2)
P2198: A/F sensor signal stuck rich (Bank 2)
Required Sensors/Components (Main) A/F sensor
Required Sensors/Components (Related) HO2 sensor
Frequency of Operation Continuous
Duration 5 seconds: Sensor voltage detection monitor
3 seconds: Sensor current detection monitor
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not present P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0300 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control)
P0451, P0452, P0453 (EVAP system)
P0500, P0722 (Vehicle Speed Sensor)
P0505 (IAC valve)
P1340 (Camshaft position sensor)
P2440 - P2447 (Secondary air injection system)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)

Sensor voltage detection monitor:
Time after engine start 30 seconds or more
A/F sensor status Activated
Fuel system status Closed-loop

Sensor current detection monitor:
Battery voltage 11 V or more
Atmospheric pressure 76 kPa (570 mmHg) or more
A/F sensor status Activated
Continuous time of fuel cut 3 to 10 seconds
ECT 75°C (167°F) or more

TYPICAL MALFUNCTION THRESHOLDS

Sensor voltage detection monitor (Lean side malfunction P2195 and P2197):
Rear heated oxygen sensor voltage 0.21 V or higher
Air fuel ratio sensor voltage Higher than 3.8 V

Sensor voltage detection monitor (Rich side malfunction P2196 and P2198):
Rear heated oxygen sensor voltage Below 0.66 V
Air fuel ratio sensor voltage Below 2.8 V

Sensor current detection monitor (High side malfunction P2195 and P2197):
Duration of following conditions 3 seconds or more
Air fuel ratio sensor current 2.2 mA or more

Sensor current detection monitor (Rich side malfunction P2196 and P2198):
Duration of following conditions 3 seconds or more
Air fuel ratio sensor current Less than 0.7 mA

CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.

A242051E34
6.281,2.177 5.375,2.177 false 5.021,1.51 4.458,1.51 false 4.208,3.5 4.083,3.5 4.083,3.5 3.948,3.354 false 2.458,1.521 2.208,1.146 false 4.938,1.688 4.552,0.677 false 5.76,1.104 5.417,1.625 false 0.115,0.24 1.979,0.427 1.865,0.188 10 false ECT: 75°C (167°F) or more 0.156,0.802 1.073,0.969 0.917,0.167 10 false Vehicle Speed 0.635,2.281 1.073,2.49 0.438,0.208 10 false Idling 1.24,2.802 2.104,3.01 0.865,0.208 10 false Warming up 2.49,2.844 3.188,3.167 0.698,0.323 10 false 10 minutes or more 1.583,2.156 1.813,2.354 0.229,0.198 10 false [A] 2.771,1.292 3.021,1.5 0.25,0.208 10 false [B] 3.552,2.167 3.75,2.333 0.198,0.167 10 false [C] 5.125,1.292 5.323,1.458 0.198,0.167 10 false [D] 5.479,1.563 5.719,1.74 0.24,0.177 10 false [E] 6.313,2.521 6.646,2.688 0.333,0.167 10 false Time 6.083,3.115 6.313,3.333 0.229,0.219 10 false [F] 6.396,1.948 6.958,2.313 0.563,0.365 10 false 10 km/h (6 mph) 3.396,1.417 4.521,1.76 1.125,0.344 10 true 64 km/h (40 mph) or more 4.667,0.76 5.635,0.927 0.969,0.167 10 false At least 3 times 5.833,1.021 7.073,1.417 1.24,0.396 10 false Accelerator Pedal Released (Fuel-cut) 3.406,0.583 4.563,0.948 1.156,0.365 10 false Accelerator Pedal Depressed 1.188,0.781 2.813,1.156 1.625,0.375 10 false Between 60 and 120 km/h (38 and 75 mph) 4.292,3.427 5.74,3.646 1.448,0.219 10 false Refer to figure below 4.646,2.781 5.385,3.146 0.74,0.365 10 false 10 seconds or more 5.458,2.75 6.125,3.104 0.667,0.354 10 true 4 seconds or more

A371143E04
3.354,2.615 2.333,0.781 2.333,0.781 2.51,0.781 false 3.604,2.615 4.073,0.958 false 0.073,0.063 2.594,0.292 2.521,0.229 10 false Driving Pattern Detail for [C] through [E]: 0.219,0.531 1.823,0.729 1.604,0.198 10 false Reference Engine RPM 0.792,1.833 1.427,2.042 0.635,0.208 10 false 2500 rpm 0.802,2.208 1.458,2.417 0.656,0.208 10 false 1000 rpm 1.052,2.385 1.469,2.594 0.417,0.208 10 false Idling 2.083,2.979 2.5,3.188 0.417,0.208 10 false Idling 2.125,2.51 2.385,2.708 0.26,0.198 10 false [C] 2.76,1.104 3.021,1.302 0.26,0.198 10 false [D] 2.573,0.698 3.802,0.896 1.229,0.198 10 false Delay (3 seconds) 3.458,1.552 3.719,1.75 0.26,0.198 10 false [E] 4.146,0.792 5.427,0.99 1.281,0.198 10 false Detection Period t1 3.156,3.094 3.844,3.458 0.688,0.365 10 false 4 seconds or more 4.385,3.094 5.073,3.458 0.688,0.365 10 false 4 seconds or more 5.615,3.083 6.302,3.448 0.688,0.365 10 false 4 seconds or more 4.771,2.396 4.969,2.594 0.198,0.198 10 false t2 6.01,2.385 6.208,2.583 0.198,0.198 10 false t3 6.51,2.771 6.927,2.979 0.417,0.208 10 false Time 2.969,0.323 7.104,0.51 4.135,0.188 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Start the engine, and warm it up until the ECT reaches 75°C (167°F) or higher [A].

8.

On Techstream, select the following menu items to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.

9.

Drive the vehicle at between 60 km/h (38 mph) and 120 km/h (75 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Shift the transmission to 2nd gear [C].

11.

Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

12.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

HINT:

Fuel-cut is performed when the following conditions are met:

·

Accelerator pedal is fully released.

·

Engine speed is 2500 rpm or more (fuel injection returns at 1000 rpm).



13.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

14.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

16.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P2195, P2196, P2197 or P2198.

19.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F].



20.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




MONITOR RESULT

WIRING DIAGRAM

A164734E18
5.521,0.844 5.958,1.021 0.438,0.177 10 false HA1A 3.979,0.854 4.417,1.031 0.438,0.177 10 false HA1A 5.521,1.625 5.958,1.802 0.438,0.177 10 false A1A+ 4.01,1.625 4.448,1.802 0.438,0.177 10 false A1A+ 5.521,2.292 5.958,2.469 0.438,0.177 10 false A1A- 3.563,1.604 4,1.781 0.438,0.177 10 false A1A- 5.521,3.323 5.958,3.5 0.438,0.177 10 false MREL 5.521,4.042 5.958,4.219 0.438,0.177 10 false HA2A 5.521,4.823 5.958,5 0.438,0.177 10 false A2A+ 5.521,5.479 5.958,5.656 0.438,0.177 10 false A2A- 5.188,0.969 5.531,1.156 0.344,0.188 10 false D56 5.188,1.75 5.51,1.938 0.323,0.188 10 false D56 5.177,2.438 5.5,2.615 0.323,0.177 10 false D56 5.167,3.438 5.479,3.594 0.313,0.156 10 false A27 5.188,4.146 5.51,4.302 0.323,0.156 10 false D56 5.188,4.927 5.479,5.083 0.292,0.156 10 false D56 5.177,5.594 5.469,5.75 0.292,0.156 10 false D56 5.26,0.792 5.438,0.948 0.177,0.156 10 false 22 5.26,3.26 5.438,3.417 0.177,0.156 10 false 34 5.26,3.979 5.438,4.135 0.177,0.156 10 false 20 5.208,1.573 5.479,1.729 0.271,0.156 10 false 126 5.208,2.24 5.479,2.396 0.271,0.156 10 false 125 5.208,4.76 5.479,4.917 0.271,0.156 10 false 103 5.208,5.417 5.479,5.573 0.271,0.156 10 false 102 4.771,2.823 5.344,2.979 0.573,0.156 10 false Shielded 4.656,5.99 5.271,6.188 0.615,0.198 10 false Shielded 3.177,2 3.479,2.167 0.302,0.167 10 false D19 3.177,2.146 4.677,2.333 1.5,0.188 10 false A/F Sensor (for Bank 1) 3.073,5.208 3.375,5.375 0.302,0.167 10 false D20 3.073,5.333 4.573,5.521 1.5,0.188 10 false A/F Sensor (for Bank 2) 4.406,0.844 4.521,1 0.115,0.156 10 false 1 4.406,1.625 4.521,1.781 0.115,0.156 10 false 3 3.427,0.844 3.542,1 0.115,0.156 10 false 2 3.427,1.625 3.542,1.781 0.115,0.156 10 false 4 3.573,0.854 3.792,1.01 0.219,0.156 10 false +B 3.813,4.021 4.25,4.198 0.438,0.177 10 false HA2A 3.844,4.802 4.281,4.979 0.438,0.177 10 false A2A+ 3.396,4.771 3.833,4.948 0.438,0.177 10 false A2A- 4.24,4.021 4.354,4.177 0.115,0.156 10 false 1 4.24,4.802 4.354,4.958 0.115,0.156 10 false 3 3.26,4.021 3.375,4.177 0.115,0.156 10 false 2 3.26,4.802 3.375,4.958 0.115,0.156 10 false 4 3.406,4.031 3.625,4.188 0.219,0.156 10 false +B 0.802,3.594 0.917,3.75 0.115,0.156 10 false 1 0.99,3.615 1.24,3.792 0.25,0.177 10 false 1C 1.01,1.115 1.26,1.271 0.25,0.156 10 false A/F 1.625,1.563 1.927,1.74 0.302,0.177 10 false A/F 1.146,3.25 1.802,3.406 0.656,0.156 10 false EFI NO. 1 1.427,2.719 2.104,2.896 0.677,0.177 10 false EFI MAIN 2.365,0.969 2.604,1.156 0.24,0.188 10 false 1A 2.365,1.25 2.625,1.427 0.26,0.177 10 false 1A 0.271,1.25 0.49,1.448 0.219,0.198 10 false 1A 2.427,0.792 2.542,0.948 0.115,0.156 10 false 4 2.427,1.438 2.542,1.594 0.115,0.156 10 false 3 2.427,2.813 2.542,2.969 0.115,0.156 10 false 3 0.323,1.063 0.438,1.219 0.115,0.156 10 false 2 0.333,1.573 0.448,1.729 0.115,0.156 10 false 5 0.271,1.75 0.531,1.948 0.26,0.198 10 false 1B 2.365,2.406 2.604,2.583 0.24,0.177 10 false 1B 2.375,3 2.625,3.167 0.25,0.167 10 false 1B 2.427,2.229 2.542,2.375 0.115,0.146 10 false 2 1.396,3.792 2.49,3.979 1.094,0.188 10 false Integration Relay 1.333,5.927 1.833,6.125 0.5,0.198 10 false Battery 5.948,6.385 6.302,6.573 0.354,0.188 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.

·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P2195, P2196, P2197 or P2198 is output A
"DTC P2195, P2196, P2197 or P2198" and "DTC P0136, P0137, P0138, P0156, P0157 or P0158" are output A
DTC P2195, P2196, P2197 or P2198 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.



A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?



YES

3.PERFORM CONFIRMATION DRIVING PATTERN

NO

4.READ VALUE USING TECHSTREAM (TEST VALUE OF A/F SENSOR)
3.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P2195, P2196, P2197 or P2198.


k.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) B



A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING TECHSTREAM (TEST VALUE OF A/F SENSOR)
4.READ VALUE USING TECHSTREAM (TEST VALUE OF A/F SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Drive the vehicle in accordance with the drive pattern described in Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Current.


g.

Check that the status of O2 Sensor is Complete. If the status is still Incomplete, drive the vehicle according to the driving pattern again.


h.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RANGE B1S1 or RANGE B2S1.


i.

Check the test value of the air fuel ratio sensor output current during fuel-cut.

Result
Result Proceed to
Within normal range (0.7 mA or higher, and below 2.2 mA) A
Outside normal range (below 0.7 mA, or 2.2 mA or higher) B



A

5.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF A/F SENSOR)

B

14.REPLACE AIR FUEL RATIO SENSOR
5.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF A/F SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result
Status of AFS Voltage B1S1 or AFS Voltage B2S1 Status of O2S B1S2 or O2S B2S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich A
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction B
Lean/Rich Lean/Rich Normal B

Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.


HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).



A

6.CHECK AIR INDUCTION SYSTEM

B

14.REPLACE AIR FUEL RATIO SENSOR
6.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leaks (See page Engine / Hybrid System>3UR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in air induction system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

7.CHECK EXHAUST GAS LEAK

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

7.CHECK EXHAUST GAS LEAK
a.

Check for exhaust gas leaks from the exhaust manifold assembly and exhaust pipes.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

8.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE

OK

9.INSPECT FUEL INJECTOR ASSEMBLY

NG

16.CHECK FUEL LINE
9.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the fuel injector (whether fuel volume is high or low, and whether injector pattern is poor) (See page Engine / Hybrid System>3UR-FE FUEL>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

10.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

11.PERFORM CONFIRMATION DRIVING PATTERN
11.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P2195, P2196, P2197 or P2198.


k.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) A
NORMAL (DTC is not output) B



A

12.REPLACE ECM

B

END

12.REPLACE ECM

NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P2195, P2196, P2197 or P2198.


k.

Check the DTC judgment result.

Result
Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





NEXT

END

14.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

15.PERFORM CONFIRMATION DRIVING PATTERN
15.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P2195, P2196, P2197 or P2198.


k.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) B



A

END

B

16.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.



OK

REPLACE FUEL PUMP ASSEMBLY

NG

REPAIR OR REPLACE FUEL LINE