Working on 12 V vehicle electrical system.
Risk of short circuits! Risk of fire!
Detach the cable from the negative (-) battery terminal.
Before performing work on electronic components, disconnect the cable from the negative (-) battery terminal to prevent damage to the electrical system or components.
When disconnecting the cable, turn the START-STOP button (engine switch) and headlight switch off and loosen the cable nut completely. Perform these operations without twisting or prying on the cable. Then disconnect the cable.
Clock settings, radio settings, audio system memory, DTCs and other data will be cleared when the cable is disconnected from the negative (-) battery terminal. Write down any necessary data before disconnecting the cable.
Use the same procedure for LHD and RHD vehicles.
The following procedure is for LHD vehicles.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for B48:
Click hereGeneral>MAINTENANCE>B48 BATTERY>REMOVAL
for B58:
Click hereGeneral>MAINTENANCE>B58 BATTERY>REMOVAL
58920C
2.REMOVE FRONT CONSOLE ARMREST ASSEMBLY
Remove the No. 1 console box silencer pad (1).
Loosen T20 screws (1).
Detach the clips (2) to remove the front console armrest assembly (1).
58822A
3.REMOVE CONSOLE UPPER REAR PANEL
Remove the No. 2 console box silencer pad (1).
Detach the clips (1) to remove the console upper rear panel (2).
58822
4.REMOVE CONSOLE SIDE PANEL
Detach the clips (2) to remove the console side panel (1).
5.REMOVE CONSOLE PANEL AND CONSOLE PANEL RETAINER
Loosen T20 screws (1).
|
Remove in this Direction |
Detach the guides (3) to remove the console panel (1) and console panel retainer (2) as shown in the illustration.
55432B
6.REMOVE INSTRUMENT PANEL FINISH LOWER PANEL
Loosen T20 screw (1) on the instrument panel finish lower panel (2).
Open the glove compartment door assembly (1).
|
Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, remove the rubber plug (1).
Loosen T20 screw behind it.
Using a moulding remover A, detach the clip (2) of the instrument panel finish lower panel (1).
Slightly pull out the instrument panel finish lower panel (1) toward you as shown in the illustration.
|
Place Hands Here |
|
Remove in this Direction |
Pull the instrument panel finish lower panel (1) straight forward, detach the guides (3) and the clip (2), and pull it out toward you.
|
Place Hands Here |
|
Remove in this Direction |
Unlock plug connection (1) and disconnect.
Detach the clip (3) to disconnect the wiring harness (2).
Remove the instrument panel finish lower panel.
58818A
7.REMOVE FRONT CONSOLE BOX COVER
|
Protective Tape |
Apply protective tape as shown in the illustration.
Using a molding remover A, detach the clips (2) of front console box cover (1).
Raise the front console box cover (1) a little.
w/o Wireless Charger:
Unlock and disconnect plug connections (1) from the front console box cover (2).
w/ Wireless Charger:
Unlock and disconnect the plug connection (1) from the front console box cover (2).
Remove the front console box cover.
58804A
8.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
Detach the clips (2) of the upper console panel sub-assembly (1).
Lift the upper console panel sub-assembly (1) up slightly.
Unlock plug connection (1) and disconnect.
Remove the upper console panel sub-assembly (2).
33550
9.REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY
55606
10.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
for LHD:
Turn the locks (3) by 90°.
Detach the guide (2).
Detach the guides (4) to remove the No. 1 instrument panel under cover sub-assembly (1).
Unlock associated plug connections and disconnect.
for RHD:
Turn the locks (3) by 90°.
Detach the guide (2).
Detach the guides (4) to remove the No. 1 instrument panel under cover sub-assembly (1).
Unlock associated plug connections and disconnect.
55607
11.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Turn the locks (3) by 90°.
Detach the guide (2).
Detach the guides (4) to remove the No. 2 instrument panel under cover sub-assembly (1).
Unlock plug connections and disconnect.
58801D
12.REMOVE CONSOLE BOX ASSEMBLY
Loosen T20 screw (1) on the console box assembly (2) on the left.
Loosen T20 screw (1) on the console box assembly (2) on the right.
Loosen T20 screws (1) on the console box assembly (2) on the front.
Unlock plug connection (1) and disconnect.
Loosen bolts (1).
Remove the console box assembly (2).
55618A
13.REMOVE CONSOLE BOX CUP HOLDER
Perform this procedure only when replacement of the console box cup holder is necessary.
Loosen T20 screws (1).
Remove the console box cup holder (2).
58821A
14.REMOVE CONSOLE PANEL
Perform this procedure only when replacement of the console panel or console panel retainer is necessary.
Loosen T20 screws (1).
Detach the clips (2).
Remove the console panel (3).
55900
15.REMOVE AIR CONDITIONING CONTROL ASSEMBLY
Perform this procedure only when replacement of the instrument panel finish lower panel is necessary.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL
58916
16.REMOVE BOX BOTTOM MAT (w/o Wireless Charger)
Perform this procedure only when replacement of the box bottom mat is necessary.
Remove the box bottom mat.
861C0
17.REMOVE MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (w/ Wireless Charger)
Perform this procedure only when replacement of the front console box cover is necessary.
Click hereVehicle Interior>POWER OUTLETS (INT)>WIRELESS CHARGER ASSEMBLY>REMOVAL
86190C
18.REMOVE NO. 1 STEREO JACK ADAPTER ASSEMBLY
Perform this procedure only when replacement of the front console box cover is necessary.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO JACK ADAPTER ASSEMBLY>REMOVAL
84720J
19.REMOVE PATTERN SELECT SWITCH ASSEMBLY
Perform this procedure only when replacement of the upper console panel sub-assembly is necessary.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>COMBINATION SWITCH (for Console Box)>REMOVAL
84390B
20.REMOVE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
Perform this procedure only when replacement of the upper console panel sub-assembly is necessary.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>REMOVAL
84780A
21.REMOVE REMOTE OPERATION CONTROLLER ASSEMBLY
Perform this procedure only when replacement of the upper console panel sub-assembly is necessary.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY CONTROLLER>REMOVAL
58911G
22.REMOVE NO. 1 BOX PANEL
Perform this procedure only when replacement of the No. 1 box panel is necessary.
Loosen T20 screws (1).
Detach the claw (2) and guides (3).
Remove the No. 1 box panel (4).
23.REMOVE EMERGENCY LOUDSPEAKER
Perform this procedure only when replacement of the No. 1 instrument panel under cover sub-assembly is necessary.
Click hereAudio / Visual / Telematics>TELEMATICS>EMERGENCY LOUDSPEAKER>REMOVAL
81080J
24.REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Foot light)
Perform this procedure only when replacement of the instrument panel under cover sub-assembly is necessary.
for Driver Side
Click hereVehicle Interior>LIGHTING (INT)>FOOTWELL LIGHT>REMOVAL
for Front Passenger Side
Click hereVehicle Interior>LIGHTING (INT)>FOOTWELL LIGHT>REMOVAL
25.REMOVE FOOTWELL STORAGE NET
Perform this procedure only when replacement of the footwell storage net is necessary.
Detach the clips (2) to remove the footwell storage net (1).
58510H
26.REMOVE FLOOR MAT ASSEMBLY
Perform this procedure only when replacement of the floor mat assembly is necessary.
Use the same procedures for the front passenger side.
Remove the floor mat assembly (1).
Turn the No. 1 mat set plates (1) by 90° and remove upward from the front floor carpet assembly.
Perform this procedure only when replacement of the No. 1 mat set plate is necessary.