Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A116143E34

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.


WIRING DIAGRAM


A161382E02


A161383E02


INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
SYSTEM OK
B


2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and Techstream ON.

  1. Check the communication between the Techstream and ECM.

    Result:

    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3.CHECK MIL (THROTTLE BODY)
  1. Disconnect the throttle body connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle body connector.



A
REPLACE THROTTLE BODY ASSEMBLY (Click here)
B


4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL ASSEMBLY (Click here)
B


5.CHECK MIL (PRESSURE SENSOR [BANK 1])
  1. Disconnect the air switching valve (bank 1).

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the air switching valve (bank 1).



A
REPLACE AIR SWITCHING VALVE (Click here)
B


6.CHECK MIL (PRESSURE SENSOR [BANK 2])
  1. Disconnect the air switching valve (bank 2).

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the air switching valve (bank 2).



A
REPLACE AIR SWITCHING VALVE (Click here)
B


7.CHECK MIL (CANISTER PUMP MODULE)
  1. Disconnect the canister pump module connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the canister pump module connector.



A
REPLACE CANISTER ASSEMBLY (Click here)
B


8.PERFORM ACTIVE TEST USING MIL (VVT SENSOR [BANK 1])
  1. Disconnect the air cleaner assembly with element.

  1. Disconnect the VVT sensor (bank 1) connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor (bank 1).



A
REPLACE VVT SENSOR (BANK 1) (Click here)
B


9.CHECK MIL (VVT SENSOR [BANK 2])
  1. Disconnect the VVT sensor (bank 2) connector.

  1. Turn the ignition switch ON.

  1. Check the MIL.

    Result:

    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor (bank 2) connector.



A
REPLACE VVT SENSOR (BANK 2) (Click here)
B


10.CHECK HARNESS AND CONNECTOR
  1. Disconnect the throttle body connector.

  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the air switching valve (bank 1).

  1. Disconnect the air switching valve (bank 2).

  1. Disconnect the canister pump module connector.

  1. Disconnect the VVT sensor (bank 1).

  1. Disconnect the VVT sensor (bank 2).



    A107934E44
  1. Disconnect the A24 and D74 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A24-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A24-59 (VCP2) - Body ground
    Always
    10 kΩ or higher
    D74-80 (VCTA) - Body ground
    Always
    10 kΩ or higher
    D74-67 (VCV1) - Body ground
    Always
    10 kΩ or higher
    D74-66 (VCV2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connectors.

  1. Reconnect the canister pump module connector.

  1. Reconnect the throttle body connector.

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the air switching valve (bank 1).

  1. Reconnect the air switching valve (bank 2).

  1. Reconnect the VVT sensor (bank 1) connector.

  1. Reconnect the VVT sensor (bank 2) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)