Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A116143E37

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM


A245725E01


A245726E04


INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
SYSTEM OK
B


2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Check the communication between the Techstream and ECM.

    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3.CHECK MIL (THROTTLE BODY WITH MOTOR ASSEMBLY)
  1. Disconnect the throttle body with motor assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

HINT:
Perform "Inspection After Repair" after replacing the throttle body with motor assembly (Click here).



A
REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY (Click here)
B


4.CHECK MIL (ACCELERATOR PEDAL ROD ASSEMBLY)
  1. Disconnect the accelerator pedal rod assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (Click here)
B


5.CHECK MIL (EMISSION CONTROL VALVE SET)
  1. Disconnect the emission control valve set connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE EMISSION CONTROL VALVE SET (Click here)
B


6.CHECK MIL (NO. 2 EMISSION CONTROL VALVE SET)
  1. Disconnect the No. 2 emission control valve set connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE NO. 2 EMISSION CONTROL VALVE SET (Click here)
B


7.CHECK MIL (CANISTER PUMP MODULE)
  1. Disconnect the canister pump module connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE CANISTER PUMP MODULE (Click here)
B


8.CHECK MIL (VVT SENSOR [FOR INTAKE SIDE OF BANK 1])
  1. Disconnect the VVT sensor (for intake side of bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 1) (Click here)
B


9.CHECK MIL (VVT SENSOR [FOR INTAKE SIDE OF BANK 2])
  1. Disconnect the VVT sensor (for intake side of bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 2) (Click here)
B


10.CHECK MIL (VVT SENSOR [FOR EXHAUST SIDE OF BANK 1])
  1. Disconnect the VVT sensor (for exhaust side of bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 1) (Click here)
B


11.CHECK MIL (VVT SENSOR [FOR EXHAUST SIDE OF BANK 2])
  1. Disconnect the VVT sensor (for exhaust side of bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 2) (Click here)
B


12.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR)
  1. Disconnect the power steering oil pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE POWER STEERING OIL PRESSURE SENSOR (Click here)
B


13.CHECK HARNESS AND CONNECTOR
  1. Disconnect the throttle body with motor assembly connector.

  1. Disconnect the accelerator pedal rod assembly connector.

  1. Disconnect the emission control valve set connector.

  1. Disconnect the No. 2 emission control valve set connector.

  1. Disconnect the canister pump module connector.

  1. Disconnect the VVT sensor (for intake side of bank 1) connector.

  1. Disconnect the VVT sensor (for intake side of bank 2) connector.

  1. Disconnect the VVT sensor (for exhaust side of bank 1) connector.

  1. Disconnect the VVT sensor (for exhaust side of bank 2) connector.

  1. Disconnect the power steering oil pressure sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    A24-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A24-59 (VCP2) - Body ground
    Always
    10 kΩ or higher
    D74-80 (VCTA) - Body ground
    Always
    10 kΩ or higher
    D74-67 (VCV1) - Body ground
    Always
    10 kΩ or higher
    D74-66 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)