Home › BODY › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > One or more Power Seat Motors do not Operate

for Preparation Click here


DESCRIPTION

When a signal is input into the position control ECU and switch assembly, the ECU manages the signals received from the power seat switches, and operates each motors. If the position control ECU and switch assembly receives more than 2 motor operation signals, the motor is stopped. Manual operation is restarted after the position control ECU and switch assembly receives 1 signal only.

WIRING DIAGRAM


B352963E04


B352964E03


INSPECTION PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
  1. Check which power seat functions are malfunctioning.
    Result 
    Result
    Proceed to
    One or more power seat functions do not operate
    A
    All power seat functions do not operate
    B



B
GO to OTHER FLOW CHART (Front Power Seat does not Operate with Front Power Seat Switch) (Click here)
A


2.CHECK FRONT POWER SEAT OPERATION
  1. Check that each function of the power seat operates normally by using the power seat switches (Click here).
    Result 
    Result
    Proceed to
    Slide, front vertical and lifter functions do not operate
    A
    Reclining functions do not operate
    B
    Lumbar support adjustment function does not operate
    C
    Leg support function does not operate
    D



B
Go to step 7

C
Go to step 11

D
Go to step 15
A


3.READ VALUE USING TECHSTREAM (SLIDE, LIFTER, FRONT VERTICAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Driver Seat / Data List.

  1. Read the Data List according to the display on the Techstream.

    Driver Seat 
    Tester Display
    Measurement item/Range
    Normal Condition
    Diagnostic Note
    Front Vertical Down
    Front vertical switch signal (Downward) / ON or OFF
    ON: Front vertical switch (Downward) on
    OFF: Front vertical switch (Downward) off
    -
    Front Vertical Up
    Front vertical switch signal (Upward) / ON or OFF
    ON: Front vertical switch (Upward) on
    OFF: Front vertical switch (Upward) off
    -
    Lifter Switch Down
    Lifter switch signal (Downward) / ON or OFF
    ON: Lifter switch (Downward) on
    OFF: Lifter switch (Downward) off
    -
    Lifter Switch Up
    Lifter switch signal (Upward) / ON or OFF
    ON: Lifter switch (Upward) on
    OFF: Lifter switch (Upward) off
    -
    Slide Rear
    Sliding switch signal (Rearward) / ON or OFF
    ON: Sliding switch (Rearward) on
    OFF: Sliding switch (Rearward) off
    -
    Slide Front
    Sliding switch signal (Forward) / ON or OFF
    ON: Sliding switch (Forward) on
    OFF: Sliding switch (Forward) off
    -

    OK:
    ON or OFF is displayed on the Techstream according to the table above.



NG
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)
OK


4.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (SLIDE, LIFTER, VERTICAL MOTOR)
  1. Check the operation of the slide motor.

    1. Remove the front seat cushion frame sub-assembly LH (slide motor) (Click here).

    2. Inspect the front seat cushion frame sub-assembly LH (slide motor) .

  1. Check the operation of the lifter motor.

    1. Remove the front seat cushion frame sub-assembly LH (lifter motor) (Click here).

    2. Inspect the front seat cushion frame sub-assembly LH (lifter motor) .

  1. Check the operation of the vertical motor.

    1. Remove the front seat cushion frame sub-assembly LH (vertical motor) (Click here).

    2. Inspect the front seat cushion frame sub-assembly LH (vertical motor) .



NG
REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH)
  1. Disconnect the Z9 and Z10 position control ECU and switch assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z10-5 (SSRS) - Z3-5
    Always
    Below 1 Ω
    Z9-3 (SLD+) - Z3-4
    Always
    Below 1 Ω
    Z9-4 (SLD-) - Z3-3
    Always
    Below 1 Ω
    Z10-1 (SGND) - Z3-6
    Always
    Below 1 Ω
    Z10-3 (SSFV) - Z14-2
    Always
    Below 1 Ω
    Z9-8 (FRV+) - Z5-2
    Always
    Below 1 Ω
    Z9-5 (FRV-) - Z5-1
    Always
    Below 1 Ω
    Z10-1 (SGND) - Z14-1
    Always
    Below 1 Ω
    Z10-4 (SSRL) - Z4-4
    Always
    Below 1 Ω
    Z9-10 (LFT+) - Z4-1
    Always
    Below 1 Ω
    Z9-12 (LFT-) - Z4-2
    Always
    Below 1 Ω
    Z10-1 (SGND) - Z4-3
    Always
    Below 1 Ω
    Z10-5 (SSRS) or Z3-5 - Body ground
    Always
    10 kΩ or higher
    Z9-3 (SLD+) or Z3-4 - Body ground
    Always
    10 kΩ or higher
    Z9-4 (SLD-) or Z3-3 - Body ground
    Always
    10 kΩ or higher
    Z10-1 (SGND) or Z3-6 - Body ground
    Always
    10 kΩ or higher
    Z10-1 (SGND) or Z14-1 - Body ground
    Always
    10 kΩ or higher
    Z10-1 (SGND) or Z4-3 - Body ground
    Always
    10 kΩ or higher
    Z10-3 (SSFV) or Z14-2 - Body ground
    Always
    10 kΩ or higher
    Z9-8 (FRV+) or Z5-2 - Body ground
    Always
    10 kΩ or higher
    Z9-5 (FRV-) or Z5-1 - Body ground
    Always
    10 kΩ or higher
    Z10-4 (SSRL) or Z4-4 - Body ground
    Always
    10 kΩ or higher
    Z9-10 (LFT+) or Z4-1 - Body ground
    Always
    10 kΩ or higher
    Z9-12 (LFT-) or Z4-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY
  1. Temporarily replace the position control ECU and switch assembly with a new or normally functioning one (Click here).

  1. Check the front power seat control system (Click here).

    OK:
    Power seat operates normally.



NG
REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (Click here)
OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE) 

7.READ VALUE USING TECHSTREAM (RECLINING)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Driver Seat / Data List.

  1. Read the Data List according to the display on the Techstream.

    Driver Seat 
    Tester Display
    Measurement item/Range
    Normal Condition
    Diagnostic Note
    Reclining Rear
    Reclining switch signal (Rearward) / ON or OFF
    ON: Reclining switch (Rearward) on
    OFF: Reclining switch (Rearward) off
    -
    Reclining Front
    Reclining switch signal (Forward) / ON or OFF
    ON: Reclining switch (Forward) on
    OFF: Reclining switch (Forward) off
    -

    OK:
    ON or OFF is displayed on the Techstream according to the table above.



NG
REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)
OK


8.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)
  1. Check the operation of the reclining motor.

    1. Remove the front seatback frame sub-assembly LH (reclining motor) (Click here).

    2. Inspect the front seatback frame sub-assembly LH (reclining motor) .



NG
REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
  1. Disconnect the Z9 and Z10 position control ECU and switch assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z10-11 (SSRR) - Z6-4
    Always
    Below 1 Ω
    Z9-9 (RCL+) - Z6-2
    Always
    Below 1 Ω
    Z9-11 (RCL-) - Z6-1
    Always
    Below 1 Ω
    Z10-1 (SGND) - Z6-3
    Always
    Below 1 Ω
    Z10-11 (SSRR) or Z6-4 - Body ground
    Always
    10 kΩ or higher
    Z9-9 (RCL+) or Z6-2 - Body ground
    Always
    10 kΩ or higher
    Z9-11 (RCL-) or Z6-1 - Body ground
    Always
    10 kΩ or higher
    Z10-1 (SGND) or Z6-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY
  1. Temporarily replace the position control ECU and switch assembly with a new or normally functioning one (Click here).

  1. Check the front power seat control system (Click here).

    OK:
    Power seat operates normally



NG
REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH (Click here)
OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE) 

11.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (LUMBAR MOTOR)
  1. Check the operation of the lumbar motor.

    1. Remove the lumbar support adjuster assembly LH (lumbar motor) (Click here).

    2. Inspect the lumbar support adjuster assembly LH (lumbar motor) (Click here).



NG
REPLACE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (LUMBAR MOTOR) (Click here)
OK


12.INSPECT FRONT POWER SEAT SWITCH LH (LUMBAR SUPPORT CONTROL)
  1. Check the operation of the lumbar support control.

    1. Remove the front power seat switch LH (lumbar support control) (Click here).

    2. Inspect the front power seat switch LH (lumbar support control) (Click here).



NG
REPLACE FRONT POWER SEAT SWITCH LH (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT POWER SEAT SWITCH LH)
  1. Disconnect the Z9 position control ECU and switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z9-6 (+B2) - Z2-5 (B)
    Always
    Below 1 Ω
    Z9-1 (GND2) - Z2-2 (E)
    Always
    Below 1 Ω
    Z9-6 (+B2) or Z2-5 (B) - Body ground
    Always
    10 kΩ or higher
    Z9-1 (GND2) or Z2-2 (E) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (LUMBAR SUPPORT ADJUSTER ASSEMBLY LH - FRONT POWER SEAT SWITCH LH)
  1. Disconnect the Z7 lumbar support adjuster assembly LH (lumbar motor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z2-1 (R) - Z7-1
    Always
    Below 1 Ω
    Z2-3 (H) - Z7-2
    Always
    Below 1 Ω
    Z2-1 (R) or Z7-1 - Body ground
    Always
    10 kΩ or higher
    Z2-3 (H) or Z7-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)  

15.INSPECT FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (LEG MOTOR)
  1. Check the operation of the leg motor.

    1. Remove the front seat cushion frame sub-assembly LH (leg motor) (Click here).

    2. Inspect the front seat cushion frame sub-assembly LH (leg motor) ).



NG
REPLACE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH (Click here)
OK


16.INSPECT FRONT POWER SEAT SWITCH LH (SEAT CUSHION CONTROL)
  1. Check the operation of the seat cushion control.

    1. Remove the front power seat switch LH (seat cushion control) (Click here).

    2. Inspect the front power seat switch LH (seat cushion control) (Click here).



NG
REPLACE FRONT POWER SEAT SWITCH LH (Click here)
OK


17.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT POWER SEAT SWITCH LH)
  1. Disconnect the Z9 position control ECU and switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z9-7 (+B1) - Z15-2
    Always
    Below 1 Ω
    Z9-2 (GND1) - Z15-1
    Always
    Below 1 Ω
    Z9-2 (GND1) - Z15-4
    Always
    Below 1 Ω
    Z9-7 (+B1) or Z15-2 - Body ground
    Always
    10 kΩ or higher
    Z9-2 (GND1) or Z15-1 - Body ground
    Always
    Below 1 Ω
    Z9-2 (GND1) or Z15-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18.CHECK HARNESS AND CONNECTOR (FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH - FRONT POWER SEAT SWITCH LH)
  1. Disconnect the Z8 front seat cushion frame sub-assembly LH (leg motor) connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
Z15-5 - Z8-2
Always
Below 1 Ω
Z15-3 - Z8-1
Always
Below 1 Ω
Z15-5 or Z8-2 - Body ground
Always
10 kΩ or higher
Z15-3 or Z8-1 - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)